Irving donaldson's Comments

Comment Wall (73 comments)

You need to be a member of MyVersacamm.com to add comments!

Join MyVersacamm.com

At 3:55pm on March 11, 2020, christe crouse said…

 i have not found it yet but iam back printing again.  guess it might be under some of this furnature  will keep looking . lesson learned . thank you 

At 2:09pm on March 11, 2020, christe crouse said…

Not sure what the right senser is  to place the swab 

At 2:04pm on March 11, 2020, christe crouse said…

I am not sure where the right senser or what it is to put the swab on

At 11:11pm on August 24, 2017, Matt Cross said…

Thank you! 

Honestly, I'm not sure if they checked the tension or not. The cuts are off in the scan and feed direction. I'll upload a picture of a bad print tomorrow. 

At 2:42pm on April 19, 2017, David R. Cunningham said…

I understand about the motor being bad, I have ordered new...  What about the carriage feeling sluggish and sticking.  It's only intermittent.  ??  Not to sure.  Thank God I ordered the motor too, just in case.  :)

BTW...  Instant Motor Error on Boot up as well.

At 4:20pm on January 12, 2017, Erin Nichols said…

You told me that in the middle of holiday season when I had ZERO time to do research.
HAHAHA. well we're here now, and that's all that matters. Don't worry, I'll bother you a lot. ;)

At 4:07pm on January 12, 2017, Erin Nichols said…

Hey, man! Long time!
Spoke to Ken at Stahls yesterday and he told me to check out the forums here. 
Hoping to sign up for bootcamp in the next few months. Glad I won't have to txt you every time i have a question, I CAN JUST BOTHER YOU HERE!!! BWAHAHAHAHA.

At 11:16pm on August 30, 2016, Tshifhiwa Justice Mugwedi said…

Hi there,my roland versaworks vp 300 does not power up ,it flashes once the light at the network cble and the light on top of Printer head carriage is on but the control panel not on please help.

At 9:01am on August 2, 2016, kofi said…

Hi, I've change head cables, long data cables but the same problem

Please help

At 8:49am on August 2, 2016, kofi said…

At 8:48am on August 2, 2016, kofi said…

Hi

Please look at the nozzle test and advice.

I've changed the head cables the long data cables, the head board but the same problem

please help

At 3:52pm on March 7, 2016, Jason Chocan said…
Hi there... I am having an issue with the media lever on my VP540... It was hit hard during a move and will not even begin to do a sheet setup... I have 2 pictures I can send as well
At 8:46am on September 13, 2015, NicNap81 said…

Thank you so much.
I hope I can learn so much from you and as soon as possible to be able to contribute, too.

At 6:57pm on August 24, 2015, Kelly said…

I used to be able to make a cut contour line from a psd file with a clipping path placed into Illustrator. Now I have updated RVW and Illustrator and I'm having issues getting the swatch to apply...

At 6:55pm on August 24, 2015, Kelly said…

Hi Irving - having a bit of an issue here...

At 6:44pm on August 24, 2015, scotty said…

Hi Irving, Thanks for the welcome :)

Hoping to learn more about my new toy :) VP-300

At 4:39pm on August 6, 2015, Steve Katz said…

hey i was sent to you i have a sp300v and im having an issue with my print heat takes forever to heat up and also got grainy prints if you could email or even text or call me please tyclothing@hotmail.com or 810-728-5876

At 4:36pm on July 30, 2015, JACINDA D LOCKE said…

Thank you,  I have been looking for a place to hopefully get some answers or help troubleshooting  for a banding issue with my machine. 

At 10:49am on July 18, 2015, GL Vogue said…

Thanks For the Welcome, I have a VP 300, purchased  the Demo at a show, Rented a U-Haul and took it Home. Soon Learned You Need to be some what of a Tech, still Learning six years later,,,  But Have made a LOT of MONEY with it. Don't see much about VP 300 on this site, or am I Missing it, or not searching correctly! Will Make Some problem solving suggestion in the future. Have to run, People to see,, Money to Make... Have Great Day!!

At 1:10am on May 15, 2015, Sean Kluckow said…

Thanks for the welcome Irving--and for the service. Just left a nice long post...sorry. Hope it isn't too much info. Have found a lot of useful info on here so far. Looking forward to being part of the community!

© 2020   Created by Steven Jackson.   Powered by

Badges  |  Report an Issue  |  Terms of Service