scotty
  • Male
  • Staffordshire
  • United Kingdom
Share on Facebook
Share
  • Blog Posts
  • Discussions (37)
  • Events
  • Photos
  • Photo Albums
  • Videos

scotty's Discussions

Anyone tell me why this is happening!

Started this discussion. Last reply by irving donaldson Jul 13. 26 Replies

Hi all, my bn20 has started to band a little and not to sure why!Nothing has changed that I know of (settings) same inks and vinyl that I have used from day one... I'll attach a picture... done the…Continue

Can you mix eco sol max 1 and 2 ?

Started this discussion. Last reply by irving donaldson Nov 14, 2016. 2 Replies

Hi guy's, just a quick question...I have a BN-20 running Eco sol max inks, they were running a little low so I ordered a new set but could only find white in max 2, my white has ran out tonight so…Continue

BN-20 Servicecall 240 error?

Started this discussion. Last reply by scotty Aug 21, 2016. 7 Replies

Hi guy's, not used the printer today but it;s just thrown this message up on screen and is beeping at me, now after a good search it sounds like the main power board has gone!Dose this sound correct?…Continue

Replace or try something else?

Started this discussion. Last reply by Inobu Nov 11, 2015. 14 Replies

Hi guy's,What would you do with the yellow head on this VP300,Replace or something other?I have done the normal head soak etc...It prints OK but it could be better, added a test print...Cap…Continue

Gifts Received

Gift

scotty has not received any gifts yet

Give a Gift

 

scotty's Page

Latest Activity

irving donaldson replied to scotty's discussion Anyone tell me why this is happening!
"Agreed, it looks a lot better. Print some letters or the VW test print and see how that looks."
Jul 13
scotty replied to scotty's discussion Anyone tell me why this is happening!
"Very true Irving but had a play tonight and got it almost 100%, the print is more than good enough for me now :) There's a shadow on the image as I left the spot lights on Doh!"
Jul 12
irving donaldson replied to scotty's discussion Anyone tell me why this is happening!
"Thanks for the update, however the head still needs adjustment in service mode. See how the bottom half is shifted it should be directly in line."
Jul 12
scotty replied to scotty's discussion Anyone tell me why this is happening!
"Hi Irving, Just a little update, spoke to Xpres and they didn't help much BUT all sorted now :) Just fitted a new head/dampers, felt wiper (top went in last week) and running like new again.... just need to aline then back on track.. test print…"
Jul 11
irving donaldson replied to scotty's discussion Anyone tell me why this is happening!
"The company that sells media should have the proper profile. You can check Xpres. I think it is there under the support tab on their web site.  The attached is from there. I believe your issue is solveable with the proper settings."
Jul 7
scotty replied to scotty's discussion Anyone tell me why this is happening!
"Poli-Print Mono White Digital Vinyl (80mic) from xpres.."
Jul 7
irving donaldson replied to scotty's discussion Anyone tell me why this is happening!
"What type or which media is that?"
Jul 6
scotty replied to scotty's discussion Anyone tell me why this is happening!
"Irving, I always set it to high quality... I did drop it down and got this (attached) which came out without the lines but to poor to use for what I need :("
Jul 6
irving donaldson replied to scotty's discussion Anyone tell me why this is happening!
"You will always get some overspray and I guess some banding too. If you look at your nozzles you have missing in your black channel. Did not look like enough to cause that amount of banding, but I guess it is since all your other nozzles are good…"
Jul 6
scotty replied to scotty's discussion Anyone tell me why this is happening!
"Huge thanks for that Irving :) Just tried the GCVP and no change :( If I look close between the 2 black boxes there's a little over spray :s"
Jul 6
irving donaldson replied to scotty's discussion Anyone tell me why this is happening!
"Here are all the white ones"
Jul 6
irving donaldson replied to scotty's discussion Anyone tell me why this is happening!
"Takes a while to get used to it - let me see what I can do"
Jul 6
scotty replied to scotty's discussion Anyone tell me why this is happening!
"I think the Roland site is having a funny fit, wont let me see any profiles! and google isn't giving me any luck either, any other site where this profile can be downloaded?"
Jul 6
irving donaldson replied to scotty's discussion Anyone tell me why this is happening!
"Say it is Rolanddga - This is a forgiving profile and will work with most glossy media - the matte version to it is labeled MCVP"
Jul 6
scotty replied to scotty's discussion Anyone tell me why this is happening!
"Put all the info in and it comes up "You indicated that you are missing an item in our database." I use the Eco sol max , which it's had in from the start, running CMYK+ white < which I never use Doh!"
Jul 6
irving donaldson replied to scotty's discussion Anyone tell me why this is happening!
"You have all the vanilla ones they include with the machine. Go to the Roland site and download other options you need. GCVP used to be one of the ones they included. In the USA www.rolanddga.com under support ICC profiles is where you go and get…"
Jul 6

Profile Information

Hometown: Please include City & State
Staffordshire UK
Core Business
Other
Type of Printer/Cutter if owned:
VP-300, Camm1
Type of Heat Press if owned:
Atkins

Comment Wall (1 comment)

You need to be a member of MyVersacamm.com to add comments!

Join MyVersacamm.com

At 6:32pm on August 24, 2015, irving donaldson said…

Welcome to the MyVersaCAMM. Browse, download, ask for assistance or share your stories and work. Happy CAMMing

 
 
 

© 2017   Created by Steven Jackson - Admin.   Powered by

Badges  |  Report an Issue  |  Terms of Service