"tall question
find required font, design layout time.
probably copy digitize logo from poor jpg time
quality of vinyl cost and is it from your stock or buy in.
amount of vinyl used inc wastage.
cutting time
weeding time + tape costs
what…"
A Digital Printing Network
chris wool's Discussions
Best white profile
Started this discussion. Last reply by Steven Jackson - Admin Feb 25, 2013. 3 Replies 0 Likes
OK so who has the best white profile please.sort of okish with the SP-CLT clear but think there is better out there thanks sorry VS540Continue
Gifts Received
chris wool has not received any gifts yet
chris wool's Page
Latest Activity
chris wool replied to Joe Lamb's discussion White Static Clean Film Print Problems"the way its stored is normally the main problem i keep mine in a plastic bag in its box when not in use, to much heat dont help, some makes have a better quality backing paper. humidity and temp change is the reason for the buckling.
"
chris wool replied to Dan Gabus's discussion Small fonts problem"the head is lose or blade holder bearings, possibly a severe case of media bunching. as said not all new blades are perfect.
perfcutting is quite hard on the mechanics of the machine unless set up very carefully and i wont do it on my print cut…"
chris wool replied to Brent Bolm's discussion printed dimensions not mathcing the size in the file??? - Versaworks issue?"deference in size could be that corel measures from centre of a vector line to centre of the other line. if it has a pen width on it corel does not report the total width but when exported as a eps the total width includes the pen width…"
chris wool replied to Alex Noble's discussion Tip: Using VersaWorks to output cuts"i like it when people think a little more out side of the box.
for cut only on plotters have you looked at the roland windows printer driver (not the cut studio plug in) this will cut straight out of corel and illy .. completely bypassing vw and cut…"
chris wool replied to Dan L's discussion Help needed to print Metallic decals"Infuriating I know but it's the metallic flecks that are the problem. Whether they be large or small don't matter just the fact they are there and what most people call metallic effect.
The gray and silver are printable on a vs metallic…"
chris wool replied to Dan L's discussion Help needed to print Metallic decals"Think in this instance you will have to try screen print or air brush. Don't think there are foils available for thermal print.
One thing you have the required outlines to create the masks which quite often is a stumbling block"
chris wool replied to Dan L's discussion Help needed to print Metallic decals"Have you seen the Roland metallic print out the dark gray has a sort of metallic hue very nice colour but not bright flecks which I think you want.
Tried a few times to emulate real Metallic but failed "
chris wool replied to Ron Fothergill's discussion Very feint magenta lines in blank areas of print runing down the sheet (not across)"I will check and reseat all head cables and see what happens "
chris wool replied to Ron Fothergill's discussion Very feint magenta lines in blank areas of print runing down the sheet (not across)"Thank you Todd I hadn't ruled out the main cables as it happens at the point the head changes direction some times left and right side of the print.
During the day we may use 3 different widths of material but will still do it when it feels…"
chris wool replied to Ron Fothergill's discussion Very feint magenta lines in blank areas of print runing down the sheet (not across)"Interesting I have the same issue but intermittent and as yet not resolved same machine newish head prints are perfect thinking static related"
chris wool replied to KrazyGraphics's discussion VS300i , New head, New dampers = No print !"nightmare for you.. are you actually getting ink all the way to the waste tank. May be the capping or the pump not doing there job properly really can spoil your day "
chris wool replied to Julie's discussion Roland cutting out"Within that area should be fine
Things to consider
Stretch while laminating
Dull blade causing bunching of the media then goes out of alignment.
Extra pinch rollers on 600 material you can get a 3rd one in.
Think I noticed just the feed…"
chris wool replied to Adam Ross's discussion What would cause my design to cut off like this?"Can only guess its the fade possibly to do with layers. Transparencies. Proof might be make it a solid colour and try"
chris wool replied to Sherri Haddow's discussion White ink won't print"Presume you followed the instructions new firmware etc."
chris wool replied to Annette Thomas's discussion TrueVis VG-540 with Clear Static Cling Media"I am in the uk so suppliers may be different
Metamark md sc 105 clear"
Profile Information
- Hometown: Please include City & State
- saltash
- Core Business
- T-shirt Shop, Graphic Designer, Manufacturer
- Your Position
- owner
- Type of Printer/Cutter if owned:
- roland sc540 pro11 = Vs540 = Graphtec fc7000 130 = graphtec flatbed = PC60 =
- Type of Heat Press if owned:
- hot one
chris wool's Photos
Comment Wall (1 comment)
- At 2:02pm on October 22, 2012,
Steven Jackson - Admin said… Welcome to MyVersaCAMM.com. Please check out our forums or visit some of the blogs for helpful information. Share some of your experiences and pictures with us or start a forum question of your own for some help from other members. The blog section is for sharing stories and the forum is where you will post any questions you have.
We are glad to have you here.
Thanks for joining our community!
Steven Jackson
© 2019 Created by Steven Jackson - Admin.
Powered by
