brad brondstater's Page

John H. replied to brad brondstater's discussion tall tshirts

"Bodek and Rhodes has a lot of everything wholesale only. I like them because their main warehouse is in Philly I get next day delivery.Never did it yet but I could drive there and back in a hour or two. there are a couple more across the…"

Mar 5

Butch replied to brad brondstater's discussion tall tshirts

"Try TSC Apparel or TSF Sportswear"

Mar 5

brad brondstater posted a discussion

tall tshirts

any one know where I can get tall pocket tshirts that are short sleeve?See More

Mar 5

2 Comments 0 Likes

brad brondstater posted a discussion

Safety Banner

Where can I get some good safety banner templates and or designs to make some banners about 4 feet wide for a plant?See More

Feb 8

0 Comments 0 Likes

Steven Jackson - Admin replied to brad brondstater's discussion ink strips on print

"When you say that it starts smearing at the beginning of the print and then clears up, I think you may be seeing the captop is a bit clogged. If you have not been maintaining the captop clean and it clogs up, it will have a buildup of ink in it and…"

Jan 28

irving donaldson replied to brad brondstater's discussion ink strips on print

"All good there with profile. The problem with your heavier color inks, blacks, blues, reds is that the print is dry to the touch, but not to the pressure (stacking or print rollers). On higher production machines, they add additional heaters that…"

Jan 27

brad brondstater replied to brad brondstater's discussion ink strips on print

"I think that is what it is, but when i use all the pich rollers on cut and print some times the rollers pick up ink and ruin the graphic before it cuts it. I'm using durasol 3.5mil premium white vinyl, with media control for heat settings and…"

Jan 27

irving donaldson replied to brad brondstater's discussion ink strips on print

"My money is on the bowing of the media as Butch and Jen stated. Look for the lint being dragged as stated. Realign the vinyl and use all your pinch rollers."

Jan 27

Jennifer Jackson replied to brad brondstater's discussion ink strips on print

"I've had this before and it was because there was fuzz under the head that would drag along the print head - you may want to take a look and do a quick cleaning on it & then as Butch said realign the vinyl just to make sure you have no…"

Jan 26

Butch replied to brad brondstater's discussion ink strips on print

"first thought would head dragging because of ripple or raised area in the vinyl - posting a picture would give more info - try printing again and watch the vinyl, see if it raises off the platen when printing starts"

Jan 26

brad brondstater posted a discussion

ink strips on print

when i first start printing on the left side facing printier I get inch strips or smearing about one inch long and it ddoes it for about ad inch then clears up, when I run the pribt agin it does the same thing, I did a manuel cleaning but that did not help. Not sure what to look for. I have a vs540.ThanksSee More

Jan 26

6 Comments 0 Likes

Butch replied to brad brondstater's discussion 3m vinyl

"Grimco"

Jan 14

brad brondstater posted a discussion

3m vinyl

Were is the best place to get 3M reflective vinyl for fire trucks? I need some in 4inch width for stripeing and some wider to cut out 3inch letters?See More

Jan 14

1 Comment 0 Likes

Steven Jackson - Admin replied to brad brondstater's discussion wall leters

"Durasol application tape will work for this as well. Basically any sign media application tape should do the trick"

Dec 20, 2012

Butch replied to brad brondstater's discussion wall leters

"TIP: Let your prints dry 24 hours or more before masking. Less chance pulling print from substrate removing mask."

Dec 19, 2012