anwar shah
  • Male
  • Houston, TX
  • United States
Share on Facebook
Share
  • Blog Posts
  • Discussions (34)
  • Events
  • Photos
  • Photo Albums
  • Videos

anwar shah's Discussions

Incorrect colors

Started this discussion. Last reply by anwar shah Mar 9. 12 Replies

Hello,Does anyone know why I'm getting dark red for black and yellow for cyan on my SP300V.I just replaced all dampers and cap tops. All the connections are correct.I tried to print two bars one of…Continue

Color coming out from dark to light on SP300V

Started this discussion. Last reply by anwar shah Jan 11. 2 Replies

Hello,Does anyone know what the problem is for getting a darker print color then lighter on the same run or any? It happens when the machine is powered up, starting with a dark color and  getting…Continue

The Encoder Strip - SP300V

Started Jul 11, 2017 0 Replies

Hello All,A while ago I posted problem on my SP300V concerning print alignment and the printwalking all over the print media. You can check my problem if you search for "Still having Print/Cut…Continue

Still having Print/Cut alignment problem on SP-300V

Started Apr 14, 2017 0 Replies

Hello All,I'm still having trouble in my print/cut alignment.Last time I was told it is the wire tension. I got the wire tension meterand after picking my brains deep, I think I found out how to use…Continue

Gifts Received

Gift

anwar shah has not received any gifts yet

Give a Gift

 

anwar shah's Page

Latest Activity

anwar shah replied to anwar shah's discussion Incorrect colors
"If only I had known!"
Mar 9
irving donaldson replied to anwar shah's discussion Incorrect colors
"Get a tech, or search the google machine"
Mar 9
anwar shah replied to anwar shah's discussion Incorrect colors
"Sounds like new heads! As soon as my pockets starts to  bulge, I'll replace them. In the meantime I'll try to finish one job which is not too critical. Being the first replacement of heads since new, any common mistakes I should be…"
Mar 9
irving donaldson replied to anwar shah's discussion Incorrect colors
"In addition to what I stated above You had a good headstrike and you may have a possible cracked manifold even if you did not have the contamination - you would have a very bad black head Lastly how many shots are on those heads - those heads may be…"
Mar 9
anwar shah replied to anwar shah's discussion Incorrect colors
"Thank you for the explanation. Having done what I listed above, I now get the black coming out as dark brown and some of the colors are mixed. Like you stated, the color mix is the case of dirty encoder strip?  I have uploaded the images."
Mar 8
irving donaldson replied to anwar shah's discussion Incorrect colors
"Cross contamination can also occur when a line is blocked, the pump will fill nozzle with available ink, thus cross contamination. Also can occur with a dirty encoder strip since the head fires when it cannot read the correct position. If need…"
Mar 7
anwar shah replied to anwar shah's discussion Incorrect colors
"I'm a lot wiser now. Many thanks."
Mar 7
Butch replied to anwar shah's discussion Incorrect colors
"Cross contamination occurs when 1 captop serves 2 colors. Examples: (1) The captop does not drain allowing the colors to mix. (2) A vacuum is created when there is a leak in one of the ink lines allowing one color to be drawn into another colors…"
Mar 7
anwar shah replied to anwar shah's discussion Incorrect colors
"After sucking the cyan ink line and checking the new cyan damper, I found new cyan damper with hardly any ink. So I replaced it again. All is well now. I would like to know what "cross contamination" is , apart from the obvious, how is it…"
Mar 7
Butch replied to anwar shah's discussion Incorrect colors
"Looks right - I have no clue. In order to get wrong colors the lines have been switch or incorrect ink cartridges inserted. If using OEM carts that is not a possibility. Aftermarket  or CIS system is."
Mar 7
anwar shah replied to anwar shah's discussion Incorrect colors
"Thanks for your response. If that is the case why are yellow and magenta printing fine? According to the Rolands' drawing and my connection it looks correct. Take a look at my sketch of the connections I made... Thanks again.  "
Mar 7
Butch replied to anwar shah's discussion Incorrect colors
"Recheck ink  line connections. Sounds like the cyan yellow have been switched."
Mar 7
anwar shah posted a discussion

Incorrect colors

Hello,Does anyone know why I'm getting dark red for black and yellow for cyan on my SP300V.I just replaced all dampers and cap tops. All the connections are correct.I tried to print two bars one of black and one of cyan, both at 100%.  After about four or five triesI still get dark red instead of black and light yellow for cyan.Many thanks in advance.See More
Mar 6
anwar shah replied to anwar shah's discussion Color coming out from dark to light on SP300V
"Many thanks Irving for your response. Sounds very feasible. I assume it would be better to replace both the damper and captop? Whilst at it I can de-clog the line. How can I de-clog the line, using a syringe or is there a better way. The line you…"
Jan 11
irving donaldson replied to anwar shah's discussion Color coming out from dark to light on SP300V
"You start with a full damper and your damper is not refilling so the prints are getting lighter. So why - things to check captop damper motor clog line"
Jan 10
anwar shah posted a discussion

Color coming out from dark to light on SP300V

Hello,Does anyone know what the problem is for getting a darker print color then lighter on the same run or any? It happens when the machine is powered up, starting with a dark color and  getting lighter.I've been using the same file for a long time until just now the problem started. I did re-RIP the file again. I always do an ENT MATCH once powered up.  Any suggestions?Many thanksSee More
Jan 10

Profile Information

Hometown: Please include City & State
houston TX
Core Business
T-shirt Shop, Graphic Designer, Other
Your Position
owner
Website:
http://shahgrahics.com
Type of Printer/Cutter if owned:
SP-300V
Type of Heat Press if owned:
Chinese

Comment Wall (2 comments)

You need to be a member of MyVersacamm.com to add comments!

Join MyVersacamm.com

At 11:59am on January 10, 2019, Steven Jackson - Admin said…

You may need to go to www.ning.com to resolve the issue. We do not have nay control over the ability to post once a person is a member. if you are experiencing technical issues it would need to be resolved via the ning network on their website. 

At 9:39am on January 8, 2019, irving donaldson said…

Are you signed in when sending message

 
 
 

© 2019   Created by Steven Jackson - Admin.   Powered by

Badges  |  Report an Issue  |  Terms of Service