adrian popi
  • Male
  • iasi
  • Romania
Share on Facebook
Share
  • Blog Posts
  • Discussions (7)
  • Events
  • Photos
  • Photo Albums
  • Videos

adrian popi's Discussions

artefact problem

Started this discussion. Last reply by irving donaldson Jul 17. 13 Replies

Hi. I've got some strange lines on the print. i use a VP540.there are some picture in the att for who can help me!thx!Continue

Gifts Received

Gift

adrian popi has not received any gifts yet

Give a Gift

 

adrian popi's Page

Latest Activity

irving donaldson replied to adrian popi's discussion artefact problem
"Adrian thanks for the update. So it was a communication issue. Have not seen it from that, so it would be interesting to know if the cables went bad or worked loose. Glad you have it worked out, Happy CAMMing!"
Jul 17
adrian popi replied to adrian popi's discussion artefact problem
"hi. the problem have been solved by changeing some cables. The three cables between the motherboard and the head carriage."
Jul 17
adrian popi replied to adrian popi's discussion artefact problem
"i"ve tryed to print from other computers and it was the same problem! a technician said that could be from the cable connection betwen tha mainboard and the K head! he says that the it is an electrical problem fore sure, something like a shot…"
Jul 11
Fred replied to adrian popi's discussion artefact problem
"For what it's worth.... I've experienced a similar problem. The little artifacts only appeared directly in line with the pinch rollers for some odd reason. Cannot remember why it disappeared, but it did - by itself- eventually.  Try…"
Jul 11
irving donaldson replied to adrian popi's discussion artefact problem
"Just let me know how you make out"
Jul 3
adrian popi replied to adrian popi's discussion artefact problem
"I just installed VW on my laptop and I'll try to print from this to see if is there the same problem! I will align the heads and hope that the problem dissapears! thank you for the patience!"
Jul 3
irving donaldson replied to adrian popi's discussion artefact problem
"OK more print issues Your heads are not aligned The nozzle test prints in 2 passes Your second pass should be immediate over the bottom pass. If you look your are shifted to the left. It could be from a head strike. That would make it hard to have…"
Jul 3
adrian popi replied to adrian popi's discussion artefact problem
"hi. i've got the tests!"
Jul 3
irving donaldson replied to adrian popi's discussion artefact problem
"Maybe I should have explain in addition to helping you with your issue I was addressing your print issue. Print issue: the black you are using CMYK is a mixture of CMYK - it is overflowing on the edge due to slow captop drain/wrong profile/or heat…"
Jul 2
adrian popi replied to adrian popi's discussion artefact problem
"i'm using a CMYK black. i will send you a test tomorrow from the office. those lines appers usually in the middle zone of the printer. in fact, if the media is smaller then 700mm, they do not apper. at the E is not the design...it is a problem!"
Jul 2
irving donaldson replied to adrian popi's discussion artefact problem
"The too much ink is on your graphics - a different issue than those lines. So I told you what I think it could be and you ask different questions without addressing the ones I ask. I could have told you it was not an encoder issue, that is why I did…"
Jul 2
adrian popi replied to adrian popi's discussion artefact problem
"it is not too much ink. they are some lines like a nozzle test but only on black. i thought it was Sheet Linear Scale and i've chanege it but the problem is still there. you think it it a with de pc rather than a problem with the versacam? thx!"
Jul 2
irving donaldson replied to adrian popi's discussion artefact problem
"Post your nozzle test Are you using a CMYK black - too much ink and the ink is smearing? Roll out your media roll a few feet - The lines are equally spaced and are printed under our print - if your media is clean the look at your image and depending…"
Jul 2
adrian popi posted a discussion

artefact problem

Hi. I've got some strange lines on the print. i use a VP540.there are some picture in the att for who can help me!thx!See More
Jul 2
adrian popi is now a member of MyVersacamm.com
Jul 2

Profile Information

Hometown: Please include City & State
pascani, romania
Core Business
Promotional Company
Your Position
graphic designer
Type of Printer/Cutter if owned:
roland vp-540

Comment Wall (1 comment)

You need to be a member of MyVersacamm.com to add comments!

Join MyVersacamm.com

At 12:59pm on September 19, 2017, Stella Kwale said…

Good Day,

How is everything with you, I picked interest on you after going through your short profile and deemed it necessary to write you immediately. I have something very vital to disclose to you, but I found it difficult to express myself here, since it's a public site.Could you please get back to me on:( mrsstellakwale5888@gmail.com) ) for the full details.

Have a nice day

Thanks God bless.

Mrs Stella.

 
 
 

© 2017   Created by Steven Jackson - Admin.   Powered by

Badges  |  Report an Issue  |  Terms of Service