SYYED SHAKEER
  • Male
  • Trinidad and Tobago
Share on Facebook
Share
  • Blog Posts
  • Discussions (7)
  • Events
  • Photos
  • Photo Albums
  • Videos

SYYED SHAKEER's Discussions

CUTTING PROBLEMS ! Help Meh !

Started this discussion. Last reply by Todd Collins Mar 9. 11 Replies

I am encountering a problem when I a trying to cut a simple rectangle 55 inches wide 2 inches high and divided in quarters . I am seeing the marching ants , the head moves along the rectangle but…Continue

CUT CONTOUR

Started this discussion. Last reply by Steven Jackson - Admin Oct 4, 2017. 5 Replies

Spring%20Flowers2.epsHope…Continue

Gifts Received

Gift

SYYED SHAKEER has not received any gifts yet

Give a Gift

 

SYYED SHAKEER's Page

Latest Activity

Todd Collins replied to SYYED SHAKEER's discussion CUTTING PROBLEMS ! Help Meh !
"XR640 definitely the cut carriage cable. Your EPS margin should be 1, not .1 one full mm.... The cable isnt very hard to change but you do have to disassemble a bit of the covers and carriage to do it."
Mar 9
SYYED SHAKEER replied to SYYED SHAKEER's discussion CUTTING PROBLEMS ! Help Meh !
"Thanks for your reply , it is the XR 640 ,  played with the eps margins all the way from .1 to .39mm ,still no luck . I am seeing the marching ant all the way . Cut carriage cable ?? could be seeing that  I have tried a lot . Is this…"
Mar 9
Todd Collins replied to SYYED SHAKEER's discussion CUTTING PROBLEMS ! Help Meh !
"1. if your versaworks in in mm, then set the EPS margin to 1 mm. 2. I dont know what machine you have, but if all else fails, and you can zoom in and actually see the dashed red lines all the way around the rectangle in versaworks, then you likely…"
Mar 9
SYYED SHAKEER replied to SYYED SHAKEER's discussion CUTTING PROBLEMS ! Help Meh !
"Followed instruction from both Mr Irvin & Mr.Todd and was able to complete initialization process . Was happy I reached this far and thought all was well . Unfortunately when I did a practice cut as before I still encountered the same…"
Mar 9
Todd Collins replied to SYYED SHAKEER's discussion CUTTING PROBLEMS ! Help Meh !
"When it says SET TO LOCK POS, you need to lock the carriage on the pin above the cap tops and hit enter, then the machine will separate the carraiges and say SET UP CUT POS. THEN you move the just the cut carriage all the way to the left against the…"
Mar 2
irving donaldson replied to SYYED SHAKEER's discussion CUTTING PROBLEMS ! Help Meh !
"LOL u might have earned a visit next time I am in TnT. Will talk next Thursday!"
Mar 2
irving donaldson replied to SYYED SHAKEER's discussion CUTTING PROBLEMS ! Help Meh !
"Because you need to move it all the way to the left end so that the cutrail engages the knife - I am on a beach so my contact maybe spotty I placed instructions above do again"
Mar 2
SYYED SHAKEER replied to SYYED SHAKEER's discussion CUTTING PROBLEMS ! Help Meh !
"I slide the cut carriage I saw the knife drop . On the control panel screen  I am seeing SET TO LOCK POS , I press enter and another message came up stating UNRECOVERABLE LIMIT SENSOR and it beeps. At this point I power off and retry to cut but…"
Mar 2
irving donaldson replied to SYYED SHAKEER's discussion CUTTING PROBLEMS ! Help Meh !
"Exactly the right picture - try this - with the machine off Hold the right, left, up arrow all at the same time and hit the power on key The cut carraige should detach from the printhead - slide the cut carraige all the way to the cutrail until the…"
Mar 2
SYYED SHAKEER replied to SYYED SHAKEER's discussion CUTTING PROBLEMS ! Help Meh !
"Here is the control panel for the XR 640"
Mar 2
irving donaldson replied to SYYED SHAKEER's discussion CUTTING PROBLEMS ! Help Meh !
"You could have knocked your cut configuration out of alignment and the machine does not know it can cut as far as to the other end. Take a picture of your control panel and post that. Did the cutcarraige or printhead run into anything or you had a…"
Mar 2
SYYED SHAKEER posted a discussion

CUTTING PROBLEMS ! Help Meh !

I am encountering a problem when I a trying to cut a simple rectangle 55 inches wide 2 inches high and divided in quarters . I am seeing the marching ants , the head moves along the rectangle but only cut  half moving to the left. When it reaches half, I see the blade holder raise hope causing it not to be cut.It continues along the rectangle path and when coming back to the right the blade holder drops and continue to cut properly , At this point only half of the rectangle is cut. When it goes…See More
Mar 1
Steven Jackson - Admin replied to SYYED SHAKEER's discussion CUT CONTOUR
"you have a TON of mesh fills and clipping masks. You will need to remove all of those manually before being able to unite without all the boxes showing up. "
Oct 4, 2017
SYYED SHAKEER replied to SYYED SHAKEER's discussion CUT CONTOUR
"The eps is a rose only , hope this file is attached properly. Please let me know if it is sent with nothing lock"
Oct 4, 2017
irving donaldson replied to SYYED SHAKEER's discussion CUT CONTOUR
"It would not open in my Illustrator - let me try on the surface All I seen was the rose!"
Oct 3, 2017
Steven Jackson - Admin replied to SYYED SHAKEER's discussion CUT CONTOUR
"are you using Corel Irv? It came in fine to Illustrator for me."
Oct 3, 2017

Profile Information

Hometown: Please include City & State
COUVA , POINT LISAS
Core Business
Embroidery, Promotional Company, Manufacturer
Your Position
OWNER
Website:
http://www.azhartents.com
Type of Printer/Cutter if owned:
SOLJET PRO4 XR640
Type of Heat Press if owned:
METALNOX

Comment Wall

You need to be a member of MyVersacamm.com to add comments!

Join MyVersacamm.com

  • No comments yet!
 
 
 

© 2018   Created by Steven Jackson - Admin.   Powered by

Badges  |  Report an Issue  |  Terms of Service