Phil Yocum
  • Male
  • Martins Ferry, OH
  • United States
Share on Facebook
Share
  • Blog Posts
  • Discussions (2)
  • Events
  • Photos
  • Photo Albums
  • Videos

Phil Yocum's Discussions

SP-300V now SP-??? Help

Started this discussion. Last reply by Cheryl Dull on Saturday. 28 Replies

I'm in need of help with my SP-300V, here's the story, a few weeks ago a storm came through and took out several pieces of equipment in our shop, our Roland SP-300V would no longer be seen by any of…Continue

Gifts Received

Gift

Phil Yocum has not received any gifts yet

Give a Gift

 

Phil Yocum's Page

Latest Activity

Cheryl Dull replied to Phil Yocum's discussion SP-300V now SP-??? Help
"I did set up the encoder. Started to set up the heads as new heads and it asked for solvent cartridges,  of course no one has those on hand so I had to order 4. Should be here Monday or Tuesday. "
Saturday
Cheryl Dull replied to Phil Yocum's discussion SP-300V now SP-??? Help
"Interesting,  I'll check that. Because I'm doing a new set up I had to order cleaning solvent cartridges so before continuing I'll check this. "
Saturday
Geoff replied to Phil Yocum's discussion SP-300V now SP-??? Help
"I had problems with my SP-300V, not find ing the carts..... While checking everything in the area of the IC ink junction boards, main junction board, cables etc, I realized that on slots 1 and 4, the IC board was touching the the metal plate above…"
Saturday
irving donaldson replied to Phil Yocum's discussion SP-300V now SP-??? Help
"It sees your cartridges, you can verify by pulling and watching  the C disappear.  Did you set up the encoder? All steps must be followed to get the board on line, because that MB talks to the servo which talks to the print board"
Saturday
Cheryl Dull replied to Phil Yocum's discussion SP-300V now SP-??? Help
"I ran Limit Initialization then Sensor check in Service mode Now I get FRSHOCPLWcw   *** * *** 1234 CCCC"
Saturday
Cheryl Dull replied to Phil Yocum's discussion SP-300V now SP-??? Help
"I ran Sensor Check, this is what I got FRSHOCPLWcw    *** L *** 1234 CCCC"
Friday
irving donaldson replied to Phil Yocum's discussion SP-300V now SP-??? Help
"Regardless you are setting your machine up prior to when a user gets it, so you have to do somethings all over even though you put the parameters. So do a Limit Position Initialize and then a Linear Encoder Setup, that is why you are getting those…"
Friday
Cheryl Dull replied to Phil Yocum's discussion SP-300V now SP-??? Help
"I have my notes.  On Linear calibration I got Call Service 0101. On Crop Sensor I got Call Service 0107"
Friday
Cheryl Dull replied to Phil Yocum's discussion SP-300V now SP-??? Help
"I installed a new battery when I put the new motherboard in, I don't believe i cleared that date. Firmware is up to date. If I recall it is 7.3, I initialize the system parameters, pushed the parameters to the printer. I believe I opened the…"
Friday
irving donaldson replied to Phil Yocum's discussion SP-300V now SP-??? Help
"Bad chips or bad board - inks matter - I hear been running X,Y, Z for years - so never view as an issue, but everything and all the basics have to be covered - at this point everything is suspect until verified! On your mainboard, Ensure your…"
Friday
Cheryl Dull replied to Phil Yocum's discussion SP-300V now SP-??? Help
"I've been using Bordeaux for years. I will run a sensor check when I get home and let you know. "
Friday
irving donaldson replied to Phil Yocum's discussion SP-300V now SP-??? Help
"Are you using OEM inks In service mode do a sensor check and let me know what codes are on the cartridges No ink no cuts"
Friday
Cheryl Dull replied to Phil Yocum's discussion SP-300V now SP-??? Help
"Motherboard is in and parameters loaded from the original board. I do get a message something to the affect that cartridges are not loaded. My machine is operating just as before the ne board, purging, setting up sheet, Versaworks can see it, etc. I…"
Friday
irving donaldson replied to Phil Yocum's discussion SP-300V now SP-??? Help
"OK where are you on it - motherboard in - you turn it on - then what"
Friday
Cheryl Dull replied to Phil Yocum's discussion SP-300V now SP-??? Help
"No, still not working."
Friday
irving donaldson replied to Phil Yocum's discussion SP-300V now SP-??? Help
"So not sure where you are and if it is working or not?"
Friday

Profile Information

Hometown: Please include City & State
Martins Ferry OH
Core Business
Graphic Designer, Promotional Company, Other
Your Position
Owner
Website:
http://www.facebook.com/pages/Ultimate-Signs-Graphics/117236485002065
Type of Printer/Cutter if owned:
Roland Versacamm SP-300V
Type of Heat Press if owned:
16 inch Hot One

Comment Wall

You need to be a member of MyVersacamm.com to add comments!

Join MyVersacamm.com

  • No comments yet!
 
 
 

© 2018   Created by Steven Jackson - Admin.   Powered by

Badges  |  Report an Issue  |  Terms of Service