Michael Gregoire
  • Male
  • Barrington, NH
  • United States
Share on Facebook
Share
  • Blog Posts
  • Discussions (41)
  • Events
  • Photos
  • Photo Albums
  • Videos

Michael Gregoire's Friends

  • Todd Collins
  • Roger
  • Michelle Mendel

Michael Gregoire's Discussions

Corel Draw color pallets

Started this discussion. Last reply by Michael Gregoire Oct 23. 2 Replies

I loaded my subscription on a new laptop. Upon opening new documents i notice i have no color pallets on right side strip. I went to my dockers, clicked on cmyk, rgb, roland and the rows show up but…Continue

sp300 versacamm laptop crash assistance needed.

Started this discussion. Last reply by Michelle Mendel Oct 23. 1 Reply

Hi Fellow cammers.,Looking for assistance. My sp300v still runs like a champ with loving care. My laptop not so well. It finally died so I purchased a new one. Unfortunately I cant find my veraworks…Continue

Versa works crashes HELP

Started this discussion. Last reply by irving donaldson Mar 2. 3 Replies

Good afternoon. I was having print issues due to bad damper last week. It was suggested I had also a head going bad. Today I installed new  blk/cyan head and  dampers. Did the thermistor check, head…Continue

Black ink is taking over the world

Started this discussion. Last reply by irving donaldson Feb 27. 3 Replies

My versacamm sp300v has decided to have an attitude today. After normal start up my first print looks terrible. No Blues. I run a test print #1 and see black in blue test strip. I run a heavy clean…Continue

Gifts Received

Gift

Michael Gregoire has not received any gifts yet

Give a Gift

 

Michael Gregoire's Page

Latest Activity

Michael Gregoire replied to Michelle Mendel's discussion Perf line
"Michelle, I do not usually tape small decals with perf lines. Example: a small oval decal fully printed laminated, I use a cut line to cut out just the decal and add an 1/8 or 1/4 inch perf line outside of it so I can pop it off roll. then just…"
Oct 23
Michael Gregoire replied to Michael Gregoire's discussion Corel Draw color pallets
"Thanks Irving,   As admin, working for now. was intermittent yesterday. Day is young . Thanks again. Mike"
Oct 23
Michelle Mendel replied to Michael Gregoire's discussion sp300 versacamm laptop crash assistance needed.
"I might have it on an older computer.  I'll have my tech guy check this weekend. I am not sure how to send it even if I find it."
Oct 23
irving donaldson replied to Michael Gregoire's discussion Corel Draw color pallets
"Try right clicking on the program and run as an administrator."
Oct 22
Michael Gregoire posted a discussion

Corel Draw color pallets

I loaded my subscription on a new laptop. Upon opening new documents i notice i have no color pallets on right side strip. I went to my dockers, clicked on cmyk, rgb, roland and the rows show up but no colors show..  I ran a corel draw repair, It was working ok earlier. Unsure if I did some thing. Restarted numeroius times. Any input woud be greatTIAMikeSee More
Oct 22
Michael Gregoire posted a discussion

sp300 versacamm laptop crash assistance needed.

Hi Fellow cammers.,Looking for assistance. My sp300v still runs like a champ with loving care. My laptop not so well. It finally died so I purchased a new one. Unfortunately I cant find my veraworks disk and I see Roland does not support download for it any more. Any help would be appreciated. I'm unsure what version it was, i believe firmware is 7. something.. The old laptop was windows 10 pro and was working great until it said no more. unsure if it was in an xp mode. Its been years.. Thanks…See More
Oct 19
irving donaldson replied to Michael Gregoire's discussion Versa works crashes HELP
"You probably trashed your VW and will need to initialize it and reset all profiles."
Mar 2
irving donaldson replied to Michael Gregoire's discussion Versa works crashes HELP
"That would do it - The old jobs were ripped under the old ink setup. So they are now trash. When you go to bring jobs in that is fine, except you brought them in under the new ink, but when it goes to process the VW is set for the old ink. you do…"
Mar 2
Michael Gregoire replied to Michael Gregoire's discussion Versa works crashes HELP
"I think I found it. Ink type was changed. "
Mar 2
Michael Gregoire posted a discussion

Versa works crashes HELP

Good afternoon. I was having print issues due to bad damper last week. It was suggested I had also a head going bad. Today I installed new  blk/cyan head and  dampers. Did the thermistor check, head alignment, head info clear, cap height adjustment, did the fill process. installed new head info. Thinking all good. Did test print from printer and looked great. Go to run a test print in versa works. CRASH and closes out. i reopened and I notice all my media profiles are all gone except vinyl I,…See More
Mar 2
irving donaldson replied to Michael Gregoire's discussion Black ink is taking over the world
"Yup"
Feb 27
Michael Gregoire replied to Michael Gregoire's discussion Black ink is taking over the world
"Thanks Butch. Cap tops are draining fine. I see no black ink  in blue damper. I will look again in am. I went ahead and changed them both to make sure they seated on top of head cap maniford good. Have pulled ink through, and run another…"
Feb 27
Butch replied to Michael Gregoire's discussion Black ink is taking over the world
"First pour cleaning fluid into the captop and see if it drains, if not drain check lines for blockage. This normally occurs at the t connector.  Check your damper to see if black ink is flowing back into the blue line. If so you have air leak…"
Feb 27
Michael Gregoire posted a discussion

Black ink is taking over the world

My versacamm sp300v has decided to have an attitude today. After normal start up my first print looks terrible. No Blues. I run a test print #1 and see black in blue test strip. I run a heavy clean and get test print #2.  I immediately add a job to queue  and run it and blues are gone within a minute with black? ink everywhere. Replaced cap tops, dampers, sponges, wipers and scraper 2 weeks ago during maintenance. It has been printing nice up to today. Any help on what to do next.......   MikeSee More
Feb 27
Butch replied to Michael Gregoire's discussion hex color code printing
"What Irv said. I will also add this, I  have a 300V and have to use Pantone Match at times."
Feb 5
irving donaldson replied to Michael Gregoire's discussion hex color code printing
"The Color Guide you provided my RGB color picker correctly identified with the hex numbers you provided. The profile I would try is MCVP, Preserve primary colors in the color management area Print with Max Impact Ensure that the printer tab in VW…"
Feb 5

Profile Information

Hometown: Please include City & State
Barrington
Core Business
Graphic Designer
Your Position
owner
Type of Printer/Cutter if owned:
sp300v

Comment Wall

You need to be a member of MyVersacamm.com to add comments!

Join MyVersacamm.com

  • No comments yet!
 
 
 

© 2020   Created by Steven Jackson.   Powered by

Badges  |  Report an Issue  |  Terms of Service