" I use 3641 with oracals profile and have no problems"
A Digital Printing Network
-
Marco Carpio
- Male
- Salt Lake City, UT
- United States
- Blog Posts
- Discussions (15)
- Events
- Photos
- Photo Albums
- Videos
Marco Carpio's Discussions
Curling material
Started this discussion. Last reply by Bob Maggio Sep 26, 2012. 4 Replies 0 Likes
HiI'm using "Generic Vinyl I" profile with Orajet 3651 gloss to print and contour cut some decals with some bleed. But after the job is done, it starts curling. I can't leave a white border on the…Continue
Floor Decal
Started this discussion. Last reply by Mike F Mar 29, 2012. 1 Reply 0 Likes
HiA customer needs a floor decal. It's gonna be applied close to her counter top. I was looking for a long lasting material in Imp. Warehouse and I found only a clear anti slip laminate, but for a…Continue
Cap Tops SP-300v
Started this discussion. Last reply by Marco Carpio Feb 2, 2012. 2 Replies 0 Likes
HiIs there somewhere a video or instructions about how to change cap tops?ThanksMarcoContinue
Magnetic material to print on
Started this discussion. Last reply by Steven Jackson - Admin Oct 13, 2011. 1 Reply 0 Likes
HiThe time to sell calendars is coming. This is why I'm looking for thinner magnetic material to print on with a SP300V. That means for a refrigerator magnet type.May I get some advice on what brand…Continue
Gifts Received
Marco Carpio has not received any gifts yet
Marco Carpio's Page
Latest Activity
irving donaldson replied to Marco Carpio's discussion Curling material"I have the same question as Dan and agreed totally with Steve suggestions. I used the material with GCVP successfully. I have found that when media is curly it tends to be over saturated and the blade is going too far into the media. So changing the…"
Steven Jackson - Admin replied to Marco Carpio's discussion Curling material"Try ccvp instead of generic vinyl. It sounds like the media is getting too saturated with ink. You may have to allow it to dry more before cutting as well. Make sure your heater settings are at the default for the profile and not on printer settings"
DanielTF3 replied to Marco Carpio's discussion Curling material"Hello Marco, what are your current cut settings for this profile? And what is your heat and dry time after print/cut?"
Marco Carpio posted a discussionCurling material
HiI'm using "Generic Vinyl I" profile with Orajet 3651 gloss to print and contour cut some decals with some bleed. But after the job is done, it starts curling. I can't leave a white border on the contour cut.What changes do I need to do in the profile to avoid this thing to happen?MarcoSee More
Marco Carpio replied to Stephanie's discussion Decorative sign blanks and other boutique type goods"I never bought from them, but I'm very insterested.
Look at their site:
http://www.signblanksusa.com/category_s/21.htm
Marco"
Mike F replied to Marco Carpio's discussion Floor Decal"Eh, better safe than sorry. Remember, you're the one that's liable if someone does slip and get hurt, especially if you knowingly cut corners. You don't necessarily have to buy an entire roll though, ask around and see if you can find…"
Marco Carpio posted a discussionFloor Decal
HiA customer needs a floor decal. It's gonna be applied close to her counter top. I was looking for a long lasting material in Imp. Warehouse and I found only a clear anti slip laminate, but for a one time job, it's very expensive.It's OK if I use regular overlaminate material (Oracal)? Some suggestions?MarcoSee More
Marco Carpio replied to Marco Carpio's discussion Cap Tops SP-300v"My printer looks different than the one in the PDF, but anyway, was very illustrative.
Following the main directions, when I was taking off one of the the cap top, I lost one spring.
Unfortunately, I'm unable to find it. I have looking…"
Marco Carpio posted a discussionCap Tops SP-300v
HiIs there somewhere a video or instructions about how to change cap tops?ThanksMarcoSee More
Steven Jackson - Admin replied to Marco Carpio's discussion Magnetic material to print on"I prefer a 20 mil magnet as it has better holding power and is still not too expensive. Imprintables sells a good quality magnetic media."
Marco Carpio posted a discussionMagnetic material to print on
HiThe time to sell calendars is coming. This is why I'm looking for thinner magnetic material to print on with a SP300V. That means for a refrigerator magnet type.May I get some advice on what brand give better results or what to avoid?See More
Steven Jackson - Admin replied to Marco Carpio's discussion Setting for windows perf?"Have you done an online update of versaworks? It should be in there after you perform the update."
Marco Carpio replied to Marco Carpio's discussion Setting for windows perf?"Admin: I don't have this profile. My VW is updated at v4.4.2
Where may i find it?"
Steven Jackson - Admin replied to Marco Carpio's discussion Setting for windows perf?"GCVP and I use max impact for color profile if possible."
Profile Information
- Hometown: Please include City & State
- Salt Lake City, Utah
- Core Business
- T-shirt Shop, Graphic Designer, Other
- Your Position
- Owner
- Website:
- http://saltlakeprintshop.com
- Type of Printer/Cutter if owned:
- Versacamm SP300v
- Type of Heat Press if owned:
- Clamshell
Comment Wall (1 comment)
- At 7:11am on June 20, 2011, Steven Jackson - Admin said…
Marco,
Welcome to MyVersaCAMM.com! You can now post to the forum, view full access to downloads and videos and share with a community of people all interested in helping each other get the most out of their printers and business. I hope that you find useful information here and that you will share your experiences with everyone so we all can grow. Please feel free to contact me with any questions you have regarding the forum, your printer, business or any other matter. I hope to see you around the forum!
Steven Jackson
MyVersacamm.com site administrator
© 2013 Created by Steven Jackson - Admin.
