Lee Engstrom
  • Male
  • Lakeville, MN
  • United States
Share on Facebook
Share
  • Blog Posts
  • Discussions (3)
  • Events
  • Photos
  • Photo Albums
  • Videos

Lee Engstrom's Discussions

Brick Wall - Arlon dpf 8000

Started this discussion. Last reply by Dennis Dunning Dec 1, 2017. 3 Replies

Anyone use the Arlon dpf 8000 for cinder block application?  I normally laminate pretty much everything that leaves my office - but is lamination required using this media? I have a request to do…Continue

SP300-V - Cut Problems after CC Cable Install

Started this discussion. Last reply by irving donaldson Nov 30, 2017. 3 Replies

Roland SP300-VHad the famed Pinchroll error, 0.0" width, cropmark errors, etc.  Replaced the Cut Carriage Cable - all errors are gone and running great.Went to cut a file that I had cut already - (it…Continue

Gifts Received

Gift

Lee Engstrom has not received any gifts yet

Give a Gift

 

Lee Engstrom's Page

Latest Activity

Dennis Dunning replied to Lee Engstrom's discussion Brick Wall - Arlon dpf 8000
"A laminate makes the Arlon 8000 easier to handle and work with, especially if you are going to be applying large graphics. We printed a large graphic on Arlon 8000, applied a laminate, and installed it on a textured rubbery surface at an indoor…"
Dec 1, 2017
Steven Jackson - Admin replied to Lee Engstrom's discussion Brick Wall - Arlon dpf 8000
"good video demonstrating the media and application http://www.youtube.com/watch?v=Yj5avQjyNyw"
Nov 30, 2017
irving donaldson replied to Lee Engstrom's discussion Brick Wall - Arlon dpf 8000
"In our Stahls training class we have used this media on cinder block with great results. No lamination, but a foam roller and heat gun. Starting with a clean surface was important and the gun eased the media going into grooves. Not much heat was…"
Nov 30, 2017
irving donaldson replied to Lee Engstrom's discussion SP300-V - Cut Problems after CC Cable Install
"Welcome - it happens and sometimes the fix is the most simplest things. When you are in the area, sometimes you just need to redo your calibrations so the machine knows what it is supposed to be doing."
Nov 30, 2017
Lee Engstrom posted a discussion

Brick Wall - Arlon dpf 8000

Anyone use the Arlon dpf 8000 for cinder block application?  I normally laminate pretty much everything that leaves my office - but is lamination required using this media? I have a request to do locker room graphics on painted cinder block walls.  Not sure if this stuff adheres enough to take paint off upon removal?  Want to give customer as much information as I can.In addition - anyone have any links to application tools they use when applying to brick (aside a heat gun).  Rollers,…See More
Nov 30, 2017
Lee Engstrom replied to Lee Engstrom's discussion SP300-V - Cut Problems after CC Cable Install
"Thank you so much.  I started out simple with doing a thorough cleaning of the Encoder Strip using 70% isopropyl alcohol.  Cuts seemed spot on afterwards (however I manually did the Environment Match and a Cut Adj before I crossed the…"
Nov 30, 2017
irving donaldson replied to Lee Engstrom's discussion SP300-V - Cut Problems after CC Cable Install
"Not sure you needed to do any of these or if you did any, but these are the things that need to be checked 1. PINCH ROLLER POSITION SENSOR CHECK 2. LIMIT POSITION & CUT DOWN POSITION INITIALIZE 3. TOOL HEIGHT ADJUSTMENT 4. TOOL PRESSURE…"
Nov 29, 2017
Lee Engstrom posted a discussion

SP300-V - Cut Problems after CC Cable Install

Roland SP300-VHad the famed Pinchroll error, 0.0" width, cropmark errors, etc.  Replaced the Cut Carriage Cable - all errors are gone and running great.Went to cut a file that I had cut already - (it is laminated with reg marks).  Cut was WAY off.  I never had cut alignment issues before replacing the CC Cable.  Farther away from the docking station and the more it fed the more out of line the cut (and yes, I design an offset to counter any small cut imperfections).Was cutting 200 decals (each…See More
Nov 29, 2017
Lee Engstrom is now a member of MyVersacamm.com
Nov 29, 2017

Profile Information

Hometown: Please include City & State
Lakeville, MN
Core Business
Graphic Designer
Your Position
Owner
Website:
http://sniperhockeydesigns.com
Type of Printer/Cutter if owned:
Roland Versacamm SP300-V

Comment Wall

You need to be a member of MyVersacamm.com to add comments!

Join MyVersacamm.com

  • No comments yet!
 
 
 

© 2018   Created by Steven Jackson - Admin.   Powered by

Badges  |  Report an Issue  |  Terms of Service