Ken Nicholson
  • Male
  • Emmaus, PA
  • United States
Share on Facebook
Share
  • Blog Posts
  • Discussions (7)
  • Events
  • Photos
  • Photo Albums
  • Videos

Ken Nicholson's Discussions

Service Manual needed

Started Feb 18 0 Replies

Does anyone know where I can get a service manual for a VersaCAMM VP-540?Thanks, KenContinue

VP540 cutter not dropping to cut

Started this discussion. Last reply by Ken Nicholson Feb 16. 4 Replies

Installed new main board.everything works except that the cutter pen does not drop to cut.the pen moves as though it's cutting but the pen doesn't come down on the vinyl.Does any know where I can…Continue

VP540 not communicating

Started this discussion. Last reply by Ken Nicholson Feb 13. 4 Replies

I have a VP-540 that lost communication with the computer.When I connect directly with the computer and ping the ip address it responds destination host unreachable.spoke with a service tech and he…Continue

Gifts Received

Gift

Ken Nicholson has not received any gifts yet

Give a Gift

 

Ken Nicholson's Page

Latest Activity

Ken Nicholson posted a discussion

Service Manual needed

Does anyone know where I can get a service manual for a VersaCAMM VP-540?Thanks, KenSee More
Feb 18
Ken Nicholson replied to Ken Nicholson's discussion VP540 cutter not dropping to cut
"Ok, Where can I find the instructions to do the initializations and calibrations? Are they in the owner's manual? Thanks"
Feb 16
irving donaldson replied to Ken Nicholson's discussion VP540 cutter not dropping to cut
"Ok still do all the initializations and calibrations. The board might have been reset during whatever process was done. And if the battery was removed, then all was lost. The cutter may not know where it is, although it is going through the…"
Feb 16
Ken Nicholson replied to Ken Nicholson's discussion VP540 cutter not dropping to cut
"This is the same board that was sent out for repair. I don't see any dip switches on this board. There is one jumper but that is where it was before repair, I took pics before sending it out."
Feb 16
irving donaldson replied to Ken Nicholson's discussion VP540 cutter not dropping to cut
"Did you set all the dip switches, do all the calibrations and initializations for the new board, or did you pull the info from the last board and place them in the new board."
Feb 15
Ken Nicholson posted a discussion

VP540 cutter not dropping to cut

Installed new main board.everything works except that the cutter pen does not drop to cut.the pen moves as though it's cutting but the pen doesn't come down on the vinyl.Does any know where I can find a schematic for the VP-540?I'm thinking I may have damaged one of the ribbons while changing the main boardbut would like to see if I can determine which one might affect the cutter.Thanks, KenSee More
Feb 15
Ken Nicholson replied to Ken Nicholson's discussion VP540 not communicating
"Much appreciated, Thank You."
Feb 13
irving donaldson replied to Ken Nicholson's discussion VP540 not communicating
"OK different issue, I will see if I can pull up the manual on the cutter and see if I see a fix/setting."
Feb 12
Ken Nicholson replied to Ken Nicholson's discussion VP540 not communicating
"Thank you, that's what it was . incorrect IP setup. Everything works now but the cutter, it traces ther cutline but the pen never comes down on the vinyl."
Feb 12
irving donaldson replied to Ken Nicholson's discussion VP540 not communicating
"Usually there is a story not told. Did someone hit the cable while it was plugged in, causing it to dislodge the RJ45 connector? Did you check the cabling? Did you try the Microsoft protocol as an IP address: with the NIC on the computer set to…"
Feb 12
Ken Nicholson posted a discussion

VP540 not communicating

I have a VP-540 that lost communication with the computer.When I connect directly with the computer and ping the ip address it responds destination host unreachable.spoke with a service tech and he says bad main board.sent board out for repair (1250) reinstalled board and get same response.is there another component that could be damaging the main board?Any hints greatly appreciated.See More
Feb 10

Profile Information

Hometown: Please include City & State
Palmetto, Florida
Core Business
Graphic Designer, Other
Your Position
Owner
Type of Printer/Cutter if owned:
VersaCamm 540

Comment Wall

You need to be a member of MyVersacamm.com to add comments!

Join MyVersacamm.com

  • No comments yet!
 
 
 

© 2021   Created by Steven Jackson.   Powered by

Badges  |  Report an Issue  |  Terms of Service