"The felt is never cleaned (felt) if it is crudy, then change - the machine cannot detect that
Wiper, if it is curling then change - machine cannot detect that - If you are wiping it weekly with the cleaning solvent and around the top when you do a…"
A Digital Printing Network
John Simons's Discussions
BN-20 Wiper & Felt wiper Replacement / Maintenance Schedule
Started this discussion. Last reply by irving donaldson Jun 12. 4 Replies 0 Likes
Hi All, I have a BN-20 - does anybody know or can advise re the maintenance schedule for changing the Felt Wiper & Rubber wipers? (I have had the machine for about 1.5 years and not had…Continue
BN20 Cutting issues
Started this discussion. Last reply by John Simons Nov 28, 2018. 7 Replies 0 Likes
Hi All, I have a BN20 that is not cutting correctly.There are times it cuts through the backing material and leaves partially cut areas on other areas of the design. I have tried the following…Continue
Gifts Received
John Simons has not received any gifts yet
John Simons's Page
Latest Activity
John Simons replied to John Simons's discussion BN-20 Wiper & Felt wiper Replacement / Maintenance Schedule"Hi Irving many thanks for reply.
Re wipers, had the printer 1.5 years now and never received message to replace either of them. (Printer is used most days)
Re Win 10 driver:- you have to use the one for Win 8 (As specified by Roland)
BN20…"
"BN 20 has a different driver for Win10
As for your wiper and felt - do a visual inspection or just wait for the notification, which goes by wipes/hours"
John Simons replied to John Simons's discussion BN-20 Wiper & Felt wiper Replacement / Maintenance Schedule"Anybody? or does nobody maintain or change the wipers?"
John Simons posted a discussionBN-20 Wiper & Felt wiper Replacement / Maintenance Schedule
Hi All, I have a BN-20 - does anybody know or can advise re the maintenance schedule for changing the Felt Wiper & Rubber wipers? (I have had the machine for about 1.5 years and not had notification to change either of the wipers as yet.)Apart for the normal cutting problems everybody experiences with the BN20 my printer works fine!FYI. I have recently upgraded to Win 10 and the BN20 utility does not appear function correctly now.All help greatly appreciatedSee More
John Simons replied to John Simons's discussion BN20 Cutting issues"Hi, I appear to have rectified problem at the moment without fitting new cutting board
Having looked at the medias I was cutting I felt that the recommended blade cutting depth was to deep, I retracted the blade to what I felt was correct for…"
saad replied to John Simons's discussion BN20 Cutting issues"Hi, was this issue fixed? We are having the same issue and i think its that cut cartridge board ?
Appreciate your response."
"You need a tension gauge, service app, and tech manual to make the adjustment. So for the BN20 that means a Tech."
John Simons replied to John Simons's discussion BN20 Cutting issues"Hi Irving, Thanks for reply.
Level of machine:- Is level (or as near as dammit)
You talk about "cut assembly tension":- How do I ascertain this and how do I change it?
Cutting:- Machine has brand new blade and cutting strip yet is still…"
"OK with what stated, but you did not talk to the machine being on a level surface. If it is not see if the uneven cut (thru media) is on the higher side. I am still not at the board yet, but since you have it on the way, you can change and test. The…"
John Simons replied to John Simons's discussion BN20 Cutting issues"Hi Irving, thanks for input.
Re force:- I have done exactly what you have advised, started at 90 and worked down to being on 68-70, was cutting perfectly when halfway through job it went to shit and started cutting unevenly over whole job.
Did all…"
"I found on numerous user on a BN20 that the issue is cut force. All were getting uneven cuts, too much, to little, none. Never, board, strip, holder, and few times a blade. However all the time force. So ensure machine is leveled, tip is good and…"
John Simons posted a discussionBN20 Cutting issues
Hi All, I have a BN20 that is not cutting correctly.There are times it cuts through the backing material and leaves partially cut areas on other areas of the design. I have tried the following solutions to no avail:-1) Changed blade and depth2) Changed Holder3) Altered cutting force and offset4) Reviewed design / cut lines (all good)5) Changed cutting strip(This job in question was cutting great until half way though it) Have previously had problems with cutting to deep and other parts of jobs…See More
Profile Information
- Hometown: Please include City & State
- Rojales
- Core Business
- Embroidery, Screen Printing, T-shirt Shop, Promotional Company
- Your Position
- Owner
- Type of Printer/Cutter if owned:
- BN20
Comment Wall
- No comments yet!
© 2019 Created by Steven Jackson - Admin.
Powered by
