Jim Cain
  • Male
  • Newfane, NY
  • United States
Share on Facebook
Share
  • Blog Posts
  • Discussions (30)
  • Events
  • Photos
  • Photo Albums
  • Videos

Jim Cain's Friends

  • irving donaldson

Jim Cain's Discussions

Iprinthead.com

Started Jun 17 0 Replies

Anyone ever use them their prices seem to good to be true.. I emailed them said comes with head rank numbers but still a little nervous.. thanks for any help or durection..

open door error

Started Jun 7 0 Replies

have an open door error, any help not sure whats going on had to change capping station, cut carriage cable, print head then this started.. i am at my end about t2o call teck but trying to save money…Continue

CUTTING PROBLEM

Started this discussion. Last reply by irving donaldson Jun 5. 1 Reply

THE CUT FEATURE ON ROLAND SP 300V NOT WORKING READS THE MARKS FINE, THEN GOES TO CUT MOTIONS BUT THE BLADE IS NOT TOUCHING THE PAPER ANY IDEAS?Continue

Cutting problem

Started Jun 2 0 Replies

Not cutting reads the registration pts acts like it's cutting but the blade doesn't go down any ideas

Gifts Received

Gift

Jim Cain has not received any gifts yet

Give a Gift

 

Jim Cain's Page

Latest Activity

Jim Cain posted a discussion

Iprinthead.com

Anyone ever use them their prices seem to good to be true.. I emailed them said comes with head rank numbers but still a little nervous.. thanks for any help or durection..
Jun 17
Jim Cain posted a discussion

open door error

have an open door error, any help not sure whats going on had to change capping station, cut carriage cable, print head then this started.. i am at my end about t2o call teck but trying to save money if there is a easy fix.. where can i find a diagram of wiring so i can check fuses not sure which one it is. thanksSee More
Jun 7
irving donaldson replied to Jim Cain's discussion CUTTING PROBLEM
"If you talking Contour cutting then check the blade holder to insure no media clogged in the holder then check to ensure the mechanism was not damaged in a media strike check the sensor in the rear is in place"
Jun 5
Jim Cain posted discussions
Jun 2
Jim Cain replied to Jim Cain's discussion captops and print heads
"even though had 2 different spring under captop ordered new printheads  just worried about the different springs as they dont seal to the head all the way around.  is there a place to order just the springs or a part number or just go to a…"
May 30
irving donaldson replied to Jim Cain's discussion captops and print heads
"Sounds like a cracked manifold"
May 30
Jim Cain posted a discussion

captops and print heads

does anyone know where i can buy the springs that go under the captops went to change mine and there are 2 different spring and had someone come over that been working in the business over 20 yrs and does his own servicing and said that they are the wrong spring and not sealing to the print head.. inturn that has caused the head to clog tried manual cleaning, pulled ink from the dampeners and the pump getting black and blue and red ok but i can hear air when i pull from the pump.. have soaked…See More
May 27
Jim Cain replied to Jim Cain's discussion printing problem
"ok i have changed the captop and maniforlds and found out that the captop ithat was in it had 2 different springs under the cap so it wasnt sealing to the head so head dried up. looking for where i can get some springs that go under the captops and…"
May 26
irving donaldson replied to Jim Cain's discussion printing problem
"You see, all little information is important. The things you omit can lead to the wrong assistance. Once you mentioned you touch the dampers, that leads to the area of cracked manifold. Where the dampers attached to the nipple is very brittle over…"
May 20
Jim Cain replied to Jim Cain's discussion printing problem
"Also I did notice the black and yellow damper was not all the way in lastnight I did gentle push it in so it was tighter, bit I didn't do anything after that.. today was gonna go some powerful cleanings.. how many should I do or continue to…"
May 20
irving donaldson replied to Jim Cain's discussion printing problem
"I am ok with leaving the heads parked for a week in cleaning solution. However, that releases so much gunk that it will take many cleanings to push out the sludge. I do not believe in a 2 hour soak, waste of time and no movement. So yes more…"
May 20
Jim Cain replied to Jim Cain's discussion printing problem
"I hooked the pro red up did a manual cleaning then a powerful, then 2 medium had the black said the first test print where blue and red were off.. after that I tried to pull some ink through lines of the red got some in my pump.. then I did the…"
May 20
irving donaldson replied to Jim Cain's discussion printing problem
"A nozzle test of just yellow would not produce your first print. So before I go further let me say I have no idea about your issue. I will think aloud. So you have and SP two heads share yellow and magenta and cyan and black. Nozzle test no cyan and…"
May 20
Jim Cain replied to Jim Cain's discussion printing problem
"Here is the nozzle check.."
May 20
irving donaldson replied to Jim Cain's discussion printing problem
"Jim I know it may not matter to you, but a nozzle test is basic is diagnosing an issue. Not saying I am a trained eye, but I am trained eye. Lady Di knows me for way too long, and years ago she was my very first install and still she is firing on…"
May 19
Jim Cain replied to Jim Cain's discussion printing problem
"there is a picture in the first post i printed squares not a nozzel check but the the nozzels were all firing now i am getting no black or cyan.."
May 19

Profile Information

Hometown: Please include City & State
newfane
Core Business
Graphic Designer
Your Position
owner
Type of Printer/Cutter if owned:
sp300v
Type of Heat Press if owned:
hix

Comment Wall

You need to be a member of MyVersacamm.com to add comments!

Join MyVersacamm.com

  • No comments yet!
 
 
 

© 2017   Created by Steven Jackson - Admin.   Powered by

Badges  |  Report an Issue  |  Terms of Service