Jerry Lentz
  • Male
  • Cleveland, OH
  • United States
Share on Facebook
Share
  • Blog Posts
  • Discussions (7)
  • Events
  • Photos
  • Photo Albums
  • Videos

Jerry Lentz's Discussions

My dust cover is hanging off and I dont know why

Started this discussion. Last reply by irving donaldson Oct 5. 3 Replies

I wish I could say these were good pictures but I wasn't sure what I was looking for. I opened the cover to do a sheet cut and the right side fell down a little as shown. It is no longer held in…Continue

Any tips on artwork to avoid weeding? I.E backgrounds

Started this discussion. Last reply by irving donaldson Jul 30. 4 Replies

I bought my versacamm to compete with screen printing. We used to outsource our screen printing but we brought it in house with the transfers. I kjnow each method has its own strengths and weaknesses…Continue

Gifts Received

Gift

Jerry Lentz has not received any gifts yet

Give a Gift

 

Jerry Lentz's Page

Latest Activity

irving donaldson replied to Jerry Lentz's discussion My dust cover is hanging off and I dont know why
"Most times, that is all that is required! Happy CAMMing!"
Oct 5
Jerry Lentz replied to Jerry Lentz's discussion My dust cover is hanging off and I dont know why
"I found the 2 screws you mentioned and they were both very loose. I was able to slide the rod back into the hole and tighten down the screws and my door works again. Thanks a ton Irving, I just needed to know where to look."
Oct 5
irving donaldson replied to Jerry Lentz's discussion My dust cover is hanging off and I dont know why
"As a tech, I can say I feel your pain. We do not try to take off the cover in doing repairs, because we inevitably end up where you are now. I do not have specific instructions, but can tell you that buy loosening the two screws you can slide the…"
Oct 5
Jerry Lentz posted a discussion

My dust cover is hanging off and I dont know why

I wish I could say these were good pictures but I wasn't sure what I was looking for. I opened the cover to do a sheet cut and the right side fell down a little as shown. It is no longer held in place and I'm not sure if its a spring or a part fell off. I didn't hear anything fall but I checked inside and around my area anyway and did not find anything. If this is something I can fix myself I would prefer that but as I said I don't see where it went wrong.In the last picture you can see the…See More
Oct 5
Jerry Lentz liked Steven Jackson's page User shared forms
Aug 19
Jerry Lentz replied to Heather White's discussion Cutting Alignment
"Dial in your print/cut adjustment first - http://www.youtube.com/watch?v=sqQzm5gzEI4 Then always add some sort of a bleed outline is a good practice. I usually do about 8 pts for mine on larger designs."
Aug 19
Jerry Lentz replied to Jerry Lentz's discussion Issue adding a cutline on graphic
"Never mind I figured it out finally. Convert outline to object and then do the boundary and it seems that's the way to go."
Aug 3
irving donaldson replied to Jerry Lentz's discussion Any tips on artwork to avoid weeding? I.E backgrounds
"The more vinyl to remove the more easy to pull up. So tedious weeding, I try to fill the inside. On the tedious, mask then weed."
Jul 30
Jerry Lentz replied to Jerry Lentz's discussion Any tips on artwork to avoid weeding? I.E backgrounds
"Good ideas to try out thanks. The premasking method actually saved me on my last order. I found out squeegees matters alot too. I was using a handout from a trade show and when I started using a better quality one I could visibly see the mask making…"
Jul 30
irving donaldson replied to Jerry Lentz's discussion Any tips on artwork to avoid weeding? I.E backgrounds
"try to match the small stuff to the garment material, do a contour around with the same color and then it is one unit."
Jul 26
Frank Bermudez replied to Jerry Lentz's discussion Any tips on artwork to avoid weeding? I.E backgrounds
"for small letters and that need weeding I put the mask on before weeding and do the weeding on the masking sheet."
Jul 26
Vinh liked Jerry Lentz's discussion Any tips on artwork to avoid weeding? I.E backgrounds
Jul 26
Vinh liked Jerry Lentz's discussion Any tips on artwork to avoid weeding? I.E backgrounds
Jul 26
Jerry Lentz posted a discussion

Any tips on artwork to avoid weeding? I.E backgrounds

I bought my versacamm to compete with screen printing. We used to outsource our screen printing but we brought it in house with the transfers. I kjnow each method has its own strengths and weaknesses but I chose the VG-540 instead :)Natrurally, I want to match my customers artwork but alot of this has been me matching a previously screen printed job which has free floating letters and numbers. For example, A left chest logo which has a center logo and possibly the company name arc'd above and…See More
Jul 25
Jerry Lentz replied to Luis Pizano-Bermudez's discussion Stickers Lift Up
"Actually I looked again, quick addition. Most of your pop ups are on sharp edges. I remember a video of steves I was watching before I got my machine where he said to avoid those harsh angles because your blade will rip the material from the quick…"
Jul 13

Profile Information

Hometown: Please include City & State
Cleveland Ohio
Core Business
Embroidery, Vendor
Your Position
Manager
Type of Printer/Cutter if owned:
Roland VG 540
Type of Heat Press if owned:
Stahls Hotronix 16x16

Comment Wall

You need to be a member of MyVersacamm.com to add comments!

Join MyVersacamm.com

  • No comments yet!
 
 
 

© 2018   Created by Steven Jackson - Admin.   Powered by

Badges  |  Report an Issue  |  Terms of Service