James R. Lecomte
  • Harrisonburg, VA
  • United States
Share on Facebook
Share
  • Blog Posts
  • Discussions (18)
  • Events
  • Photos
  • Photo Albums
  • Videos

James R. Lecomte's Discussions

Inconsistent Cutting

Started this discussion. Last reply by James R. Lecomte Jan 17. 10 Replies

I have a problem.  Recently my VS540i has started cutting off center the further left on the sheet it goes.  In the attached picture the left image is the first cut on the run and the right image is…Continue

Tags: Cutting, VS540i

Pocket Banner Measurements

Started this discussion. Last reply by Blaine Jackett Apr 22, 2014. 1 Reply

I am about to make my first banner with pockets.  I have one question:  how far should I measure down to make the pocket?? Continue

Light Black Drying up on my vs-540i

Started this discussion. Last reply by irving donaldson Mar 29, 2014. 6 Replies

I am having a problem with the light black not printing {drying up ??} on  my vs 540i.  I print the test pattern in Cleaning during my weekly maintenance and the light black does not print, or prints…Continue

Correct Banner Profile for Printing on ARLON 13oz Gloss Banner Media

Started this discussion. Last reply by James R. Lecomte Jan 30, 2014. 7 Replies

I am preparing to print banners and I have no idea which Media Type I should select in VersaWorks.  I am using a VS-540i and printing on ARLON DPF313 13oz Gloss Banner media.  I assume I should use…Continue

Gifts Received

Gift

James R. Lecomte has not received any gifts yet

Give a Gift

 

James R. Lecomte's Page

Latest Activity

James R. Lecomte replied to James R. Lecomte's discussion Inconsistent Cutting
"I just checked the Firmware version on my VersaCAMM and it is way out of date. It is version 1.7 and Roland has version 2.3 on the website.  however, the file is for a VS640i and I have a VS540i.  I assume it is the same…"
Jan 17
irving donaldson replied to James R. Lecomte's discussion Inconsistent Cutting
"Nope, Nope, Nope Cannot stretch my arms around the graphics. You print a circle with a bleed - you get the same circle on both sides - that is one  Machine comes back and cuts - the design does not change - the cut could - that is a different…"
Jan 17
James R. Lecomte replied to James R. Lecomte's discussion Inconsistent Cutting
"Yup, that is what has me so confused!!"
Jan 17
irving donaldson replied to James R. Lecomte's discussion Inconsistent Cutting
"The Print/Cuts are great"
Jan 17
James R. Lecomte replied to James R. Lecomte's discussion Inconsistent Cutting
"actually, the decals have a dark navy border with a very generous bleed."
Jan 17
James R. Lecomte replied to James R. Lecomte's discussion Inconsistent Cutting
"Here is the test print."
Jan 17
James R. Lecomte replied to James R. Lecomte's discussion Inconsistent Cutting
"this print had only 2, but I have tried using all 7 and get the same result.  Where is auto env match?  not familiar with that setting."
Jan 17
chris wool replied to James R. Lecomte's discussion Inconsistent Cutting
"morning i presumed that the picture was taken after it has been weeded and james has used a generous black bleed"
Jan 17
irving donaldson replied to James R. Lecomte's discussion Inconsistent Cutting
"Agree with all Chris stated but I see another issue. Your issue happened during printing. Both designs should be the same with one having a bad cut. The shifting happened during the printing and not during the cutting. If during the cutting, the…"
Jan 16
chris wool replied to James R. Lecomte's discussion Inconsistent Cutting
"if the first cut is satisfactory then the print and cut adjustments are fine. how many pinch rollers are you using and is it laminated before cut"
Jan 16
James R. Lecomte posted a discussion

Inconsistent Cutting

I have a problem.  Recently my VS540i has started cutting off center the further left on the sheet it goes.  In the attached picture the left image is the first cut on the run and the right image is the last cut across the roll.  I am using a 54" wide roll of decal material.  I have gone into the Print/Cut Adjustment menu and the test print is perfect.  I have slowed down the Cut Speed to 10 cm/sec and this has helped a little bit.  Any ideas?See More
Jan 16
James R. Lecomte replied to James Fenerty's discussion Looking for latest version of VW
"I am running version 5.5.1 on windows 10.  VW operates fine for me.  I had to install VS from my disk.  The first time I ran VW it updated.  The last time I checked Roland did not give out version 6 to those of us with older…"
Jan 8

Profile Information

Hometown: Please include City & State
Harrisonburg, VA
Core Business
Screen Printing, Promotional Company
Your Position
Machine Operator
Type of Printer/Cutter if owned:
VersaCAMM VS 540i
Type of Heat Press if owned:
Hotronix Clam 16 X 20

Comment Wall

You need to be a member of MyVersacamm.com to add comments!

Join MyVersacamm.com

  • No comments yet!
 
 
 

© 2020   Created by Steven Jackson.   Powered by

Badges  |  Report an Issue  |  Terms of Service