James Fenerty
  • Male
  • Philadelphia, PA
  • United States
Share on Facebook
Share
  • Blog Posts
  • Discussions (100)
  • Events
  • Photos
  • Photo Albums
  • Videos

James Fenerty's Friends

  • Kimo
  • Mobil Image Werke, LLC
  • J_H
  • Steven Jackson
  • CYW
  • irving donaldson

James Fenerty's Discussions

Grit Roller Problem

Started this discussion. Last reply by irving donaldson Jul 24. 11 Replies

HiI have A VS - 300i and i have been trying to search this and find out some info. what is happening is i usually use 30" material for most jobs, i have a roll of 15 or 16 " material and i was going…Continue

Looking for latest version of VW

Started this discussion. Last reply by irving donaldson Jan 10. 4 Replies

I have a vs 300i and i am upgrading my system from windows 7 to windows 10 I used my disc to install VW on my windows 7 computer VW version is 5.5.1. i think the disc is 5.0i have searched this site…Continue

Nozzle check and print issue

Started this discussion. Last reply by James Fenerty Aug 27, 2018. 8 Replies

Hello everyone, 20180822_140155.jpgi am having a problem with my vs 300i about a week ago i…Continue

Where can i Buy Cutting Strip for vs 300i

Started this discussion. Last reply by irving donaldson Jan 22, 2018. 3 Replies

Can anyone point me in the right direction to buy this? Both Imprintables & Stahls dosen't carry themJimContinue

Gifts Received

Gift

James Fenerty has not received any gifts yet

Give a Gift

 

James Fenerty's Page

Latest Activity

irving donaldson replied to James Fenerty's discussion Grit Roller Problem
"C clip on the side"
Jul 24
Wade Knarr replied to James Fenerty's discussion Grit Roller Problem
"How do you get the pinch roller assembly out to replace it? I have 2 new ones but can not figure out how to switch out."
Jul 21
irving donaldson replied to James Fenerty's discussion Grit Roller Problem
"The cutters are easier to get to, not so much the print/cut. For that reason, it is deemed only a factory repair level, which is in Japan. It does not make the machine unusable, you just cannot get the full width. If it was a warrantied repair, I am…"
Jul 19
chris wool replied to James Fenerty's discussion Grit Roller Problem
"ok sorry blue lines it is now i am back in front of mine and understand your problem, i have come across separating grit rollers before think it was a summa or graphtec but there was a grub screw to reset presume when these are made possibly a…"
Jul 19
James Fenerty replied to James Fenerty's discussion Grit Roller Problem
"Irv, Thanks for the reply and the info...... well that Sucks..... I'm grateful that i can still use this but from a material stand point over time that is added cost and will add up. I put my 30 inch material back in and used 4 rollers and i is…"
Jul 19
James Fenerty replied to James Fenerty's discussion Grit Roller Problem
"Chris,  thanks for the reply, maybe my wording is not right, i was using a roll of 15" material and you only have 1 option with the rollers to use the entire 15" width. the far right roller  ( which has 3 roller positions left…"
Jul 19
chris wool replied to James Fenerty's discussion Grit Roller Problem
"evening just re read that several times and think its a case of incorrect roller positions, the machine reads the two outer ones only and must be positioned under the white lines only so normal use the left and right roller has to be on the material…"
Jul 18
irving donaldson replied to James Fenerty's discussion Grit Roller Problem
"Confirming the Grit Rollers cannot be fixed. Those were my instructions and I just went up and verified on the tech side of the house. If you have one that is moving independent, then a piece wore out or failed. If you did strip the machine down to…"
Jul 18
James Fenerty replied to James Fenerty's discussion Grit Roller Problem
"Hi, And thanks for the reply i will take a look at this tomorrow, my question is if the hold down wheel doesn't work at the far right position then in theory it shouldn't work when I move it over to the next position? Also should I be able…"
Jul 17
Kimo replied to James Fenerty's discussion Grit Roller Problem
"Hi I believe the problem is with the hold down wheels on your printer. Replace the wheels, or just the one slipping, but best to replace both. The rubber often breaks away from the brass making reg. impossible, if you look closely you will see what…"
Jul 17
Wade Knarr replied to James Fenerty's discussion Grit Roller Problem
"I am having this same exact issue. Hopefully someone can give some insight to the possible fix."
Jul 17
James Fenerty posted a discussion

Grit Roller Problem

HiI have A VS - 300i and i have been trying to search this and find out some info. what is happening is i usually use 30" material for most jobs, i have a roll of 15 or 16 " material and i was going to use it for some left chest designs, I loaded it using the far right pinch roller and the first pinch roller to the left outside of the 6" area.The material prints no problem but when it cuts it is feeding the material on far right side out faster and thus registration is off. First thing i did…See More
Jul 16
irving donaldson replied to James Fenerty's discussion Looking for latest version of VW
"Your old version will work on windows 10 and in your preferences you can set it to update from the Roland web site. As stated VW 6 will work with i versions and not the models b4. This site never post versions of VWs - you need to have a registered…"
Jan 10
James R. Lecomte replied to James Fenerty's discussion Looking for latest version of VW
"I am running version 5.5.1 on windows 10.  VW operates fine for me.  I had to install VS from my disk.  The first time I ran VW it updated.  The last time I checked Roland did not give out version 6 to those of us with older…"
Jan 8
James Fenerty replied to James Fenerty's discussion Looking for latest version of VW
"Chris, thank you i will look into that, How long has V6 been out? Anyone know if it has any bugs ? thanks for the reply JIm"
Jan 8
chris wool replied to James Fenerty's discussion Looking for latest version of VW
"not a 100% sure but because its a (i) version i think you can download V6 from rolands web site."
Jan 8

Profile Information

Hometown: Please include City & State
Pennsylvania
Core Business
Screen Printing
Your Position
owner
Type of Printer/Cutter if owned:
BN-20
Type of Heat Press if owned:
Stahls draw press

Comment Wall

You need to be a member of MyVersacamm.com to add comments!

Join MyVersacamm.com

  • No comments yet!
 
 
 

© 2020   Created by Steven Jackson.   Powered by

Badges  |  Report an Issue  |  Terms of Service