Jacob barrio
  • Male
  • Las Cruces, NM
  • United States
Share on Facebook
Share
  • Blog Posts
  • Discussions (13)
  • Events
  • Photos
  • Photo Albums
  • Videos

Jacob barrio's Discussions

How to set the offset on sp 540

Started Jul 16 0 Replies

How do I set the correct offset setting on my sp540v?Continue

How to replace a cutting strip on a 540v

Started this discussion. Last reply by irving donaldson Jul 2. 1 Reply

can anyone tell me how to properly replace a cutting strip on a sp-540v?Continue

How to change out Grit Rollers?

Started this discussion. Last reply by irving donaldson Jul 4. 6 Replies

Has anybody ever changed out grit rollers?how difficult is it?About how long did it take?how much of the machine do you have to take apart?Thanks.Continue

Yellow is printing kinda greenish

Started Jun 14 0 Replies

I am printing a test print straight from Versaworks and the yellow is coming out with a greenish tone to it.what could it be?I have attached a pic for you to see.Continue

Gifts Received

Gift

Jacob barrio has not received any gifts yet

Give a Gift

 

Jacob barrio's Page

Latest Activity

Jacob barrio replied to Allan Steinberg's discussion Problem cutting with Versacamm VS 540i
"I have the same problem.  I bought a brand new blade holder, new blade and put a new cutting strip. check my Offset and its correct. what else could be the problem?"
Jul 17
Jacob barrio posted a discussion

How to set the offset on sp 540

How do I set the correct offset setting on my sp540v?See More
Jul 16
irving donaldson replied to Jacob barrio's discussion How to change out Grit Rollers?
"How much blade is out and is it a new blade. You want us to image what you are seeing, I can keep guessing!"
Jul 4
Jacob barrio replied to Jacob barrio's discussion How to change out Grit Rollers?
"what do you think would cause the blade holder and pretty much that whole assembly to vibrate wile its cutting.  It doesnt vibrate 100 % of the time while its cutting. Only when the material is being fed forward or backward.   And so…"
Jul 4
Jacob barrio replied to Jacob barrio's discussion How to change out Grit Rollers?
"thanks i will add the scotch tape and re place the blade with a brand new one. lets see how it goes."
Jul 2
irving donaldson replied to Jacob barrio's discussion How to replace a cutting strip on a 540v
"All cutting strips are the same Order the replacement for your machine Dig out the old one starting with either end Clean track with alcohol to remove debris and old adhesive Replace in slot with new one and trim end to fit"
Jul 2
irving donaldson replied to Jacob barrio's discussion How to change out Grit Rollers?
"Jacob answer is below my preable! Preable: State what the problem is, not what your solution to the problem! Solution: Yes one of two things for sure: 1. Cutting strip is exhausted have gouged marks (cover with scotch tape until new one comes) 2.…"
Jul 2
Jacob barrio replied to james's discussion Versacamm SP-300i wont print after manual head clean
"It could be that the fuses that control the printheads  are blown."
Jul 2
Jacob barrio replied to Jacob barrio's discussion How to change out Grit Rollers?
"ok, thanks. I figured out the problem is not the grit rollers. Its either the cutting strip or the blade holder. although the very right grit roller closest to the print heads was pretty dirty with dried up ink........ So that is clean now. But…"
Jul 1
Jacob barrio posted a discussion

How to replace a cutting strip on a 540v

can anyone tell me how to properly replace a cutting strip on a sp-540v?See More
Jul 1
irving donaldson replied to Jacob barrio's discussion How to change out Grit Rollers?
"There are lots of parts on the CAMM that can be changed. However, the grit rollers cannot and for that reason doing magnets directly are deterred!  Let's see if anyone attempted the feat!"
Jun 30
Jacob barrio posted discussions
Jun 30
Jacob barrio replied to Sam's discussion SP-540v, Did I damaged the main board?
"yup its the fuse. I just replaced mine yesterday."
Jun 15
Jacob barrio posted discussions
Jun 14
Jacob barrio replied to Jacob barrio's discussion sp540v Printhead Fuse Location
"awesome thanks!!!"
Jun 13
Todd Collins replied to Jacob barrio's discussion sp540v Printhead Fuse Location
"The fuses are on the main board not the print cartridge board. The F2 fuse is for the black and cyan."
Jun 13

Profile Information

Hometown: Please include City & State
Las cruces
Core Business
Graphic Designer
Your Position
Owner
Website:
http://elitecarwrpaslc.com
Type of Printer/Cutter if owned:
sp-540v

Comment Wall

You need to be a member of MyVersacamm.com to add comments!

Join MyVersacamm.com

  • No comments yet!
 
 
 

© 2018   Created by Steven Jackson - Admin.   Powered by

Badges  |  Report an Issue  |  Terms of Service