Goran Stojanovic
  • Male
  • Belgrade
  • Serbia
Share on Facebook
Share
  • Blog Posts
  • Discussions (8)
  • Events
  • Photos
  • Photo Albums
  • Videos

Goran Stojanovic's Discussions

Versacamm vs420 problem with cyan

Started this discussion. Last reply by Goran Stojanovic Sep 15. 14 Replies

Hello everyone!I'm new to the forum, I've read a lot of posts with problems in the print, but I haven't found anything similar ..I would say that the member of "Brett R" had a "similar" problem, but…Continue

Gifts Received

Gift

Goran Stojanovic has not received any gifts yet

Give a Gift

 

Goran Stojanovic's Page

Latest Activity

Goran Stojanovic replied to Goran Stojanovic's discussion Versacamm vs420 problem with cyan
"Thank you for your effort and help, I'll try a little more with the cleaning, but I'm not sure it will help. I'll let you know if I make any progress. Regards, Goran"
Sep 15
irving donaldson replied to Goran Stojanovic's discussion Versacamm vs420 problem with cyan
"Goran I have absolutely no idea. Your calibration is closer to -.15 than where it is now - hard to tell with the black black head another 48 hours will not hurt.  The errant cyan and black nozzles are causing your issues. They are minor, but…"
Sep 15
Goran Stojanovic replied to Goran Stojanovic's discussion Versacamm vs420 problem with cyan
"Hi Irving, I sent a calibration test and sent an image that I printed out in 720x720dpi resolution. I really don't know what the cause of the problem is, do you have any idea what else I could try, or another 48hr cleaning. Thanks, Goran"
Sep 15
irving donaldson replied to Goran Stojanovic's discussion Versacamm vs420 problem with cyan
"Do it on the User side -  Menu \/ down arrow Calibration (after bi-direction) top block over the bottom block - no space, no overlap"
Sep 14
Goran Stojanovic replied to Goran Stojanovic's discussion Versacamm vs420 problem with cyan
"Thanks for the answers, I will try the calibration test, does the calibration test start from the service menu? or is located elsewhere."
Sep 14
irving donaldson replied to Goran Stojanovic's discussion Versacamm vs420 problem with cyan
" You have corrected some of your issues, but I see some errant cyan nozzles that may be causing  your issues to continue. The humidity is good enough to not cause static issues. Check your calibration test, it looks slightly off towards a…"
Sep 13
Goran Stojanovic replied to Goran Stojanovic's discussion Versacamm vs420 problem with cyan
"Hi Irving,  the humidity is currently around 63 degrees, the cap top is 3 months old. I sent an additional test."
Sep 13
irving donaldson replied to Goran Stojanovic's discussion Versacamm vs420 problem with cyan
"Greetings, When you take your pixs, please take them straight on. At an angle, changes what you see.  Although the changes were minute, if you compare pre and post - there where some changes. I am not sure if you require a longer soak, or if…"
Sep 12
Goran Stojanovic replied to Goran Stojanovic's discussion Versacamm vs420 problem with cyan
"Hi,  i did a 48hr headsoak cleaning, i send pictures, but it didn't help."
Sep 12
irving donaldson replied to Goran Stojanovic's discussion Versacamm vs420 problem with cyan
"Goran that is correct. Check after 24 hours incase you need to add more cleaning solvent. Fill the top so there is a slight bubble before it overflows. If it works right when you gently seat the head so it locks - when you unlock - moving it to the…"
Sep 10
Goran Stojanovic replied to Goran Stojanovic's discussion Versacamm vs420 problem with cyan
"If I understood the cleaning 48hr -headsoak, the waste hose should be closed and the printer always turned off (totally off on the rear switch)?"
Sep 10
Goran Stojanovic replied to Goran Stojanovic's discussion Versacamm vs420 problem with cyan
"Thanks Alex / Irving, Thanks for the instructionsAs far as I know the head did not have a crash.I will try to enter service mode and try a Nozzle Check.I will try a 48hr headsoak for the weekend, so I will report the results. Do I need to pay…"
Sep 10
irving donaldson replied to Goran Stojanovic's discussion Versacamm vs420 problem with cyan
"Look at your cyan - nozzles are deflected (some) - that will cause the halos and ghosting you stated. You did not state your color palette - but if it is CMYK then that is why you are seeing it in your black also. You do have a wonky K nozzle - that…"
Sep 9
Alex replied to Goran Stojanovic's discussion Versacamm vs420 problem with cyan
"Hi there Goran ,  Did you get a head crash recently? If you can access service mode and try a Nozzle Check. You might see a cyan channel having a wavy alignment on the fine nozzle test side.  Yours, "
Sep 9
Goran Stojanovic posted a discussion

Versacamm vs420 problem with cyan

Hello everyone!I'm new to the forum, I've read a lot of posts with problems in the print, but I haven't found anything similar ..I would say that the member of "Brett R" had a "similar" problem, but I hope it is not a problem up to the head of the printer?I have a problem with Versacamm vs420More precisely, when printing, for some reason, it makes "- ghosts" in cyan.I use a 4 x cmyk color refill, I send pictures with the problem and tests print.I have to say that the nozzle check is good, and…See More
Sep 9
Goran Stojanovic is now a member of MyVersacamm.com
Sep 7

Profile Information

Hometown: Please include City & State
Belgarde
Core Business
Graphic Designer
Your Position
Graphic Designer
Type of Printer/Cutter if owned:
Roland Versa camm VS420

Comment Wall (1 comment)

You need to be a member of MyVersacamm.com to add comments!

Join MyVersacamm.com

At 5:50pm on September 13, 2021, James said…

Good Day,

How is everything with you, I picked interest on you after going through your short profile and deemed it necessary to write you immediately. I have something very vital to disclose to you,but I found it difficult to express myself here, since it's a public site.Could you please get back to me on ( p3rsonalemail1@gmail.com
) for the full details.Have a nice day
Thanks God bless.

 
 
 

© 2021   Created by Steven Jackson.   Powered by

Badges  |  Report an Issue  |  Terms of Service