Eric Wyatt
  • Male
  • Fort Myers, FL
  • United States
Share on Facebook
Share

Eric Wyatt's Friends

  • Alex Chavez
  • IrOne
  • Mar Czar
  • rudy uribe
  • KnK Screen Printing

Eric Wyatt's Discussions

VS-640i Ink Migration Issue

Started Dec 10, 2018 0 Replies

Hello fellow Versacamm users. Attached is a photo of the problem I'm having with my Versacamm vs-640i. The initial Test Pattern print looks bad. However when I preform a Powerful Clean the Test…Continue

Tags: problem, migration, ink, vs-640i, vesacamm

Horizontal solid yellow & solid light magenta stripes

Started this discussion. Last reply by Eric Wyatt Nov 30, 2018. 18 Replies

Hello fellow Roland VersaCamm users. As you can see from the attached photos, I am having print color issues printing a solid yellow and solid light magenta. This was printed from the Service Mode;…Continue

Tags: magenta, stripes, light, &, solid

VersaCamm VS-300i VS-540i VS-640i Service Manual PDF Link

Started Apr 24, 2017 0 Replies

Hello All,below is a Dropbox link for the VersaCamm VS-300i VS-540i VS-640i Service Manual: Hope this helps…Continue

Tags: Manual, Service, VS-640i, VS-540i, VS-300i

Gifts Received

Gift

Eric Wyatt has not received any gifts yet

Give a Gift

 

Eric Wyatt's Page

Latest Activity

Eric Wyatt posted a discussion

VS-640i Ink Migration Issue

Hello fellow Versacamm users. Attached is a photo of the problem I'm having with my Versacamm vs-640i. The initial Test Pattern print looks bad. However when I preform a Powerful Clean the Test Pattern print is fine. However, I have to preform a Power Clean throughout the day. Here is what I have done so far:1) Replaced the Cap Top.2) Replaced the Wiper.3) Replaced the Felt Wiper.4) Clean the Encoder Scale.5) Preformed a Manual Clean.Any suggestions anyone has would be much appreciated.…See More
Dec 10, 2018
0 Comments
Eric Wyatt replied to Eric Wyatt's discussion Horizontal solid yellow & solid light magenta stripes
"Thank you very much for that info. Do you have any suggestions regarding the possibility of a suction or electrical issue? Would the "CHOKE VALVE" function help?"
Nov 30, 2018
irving donaldson replied to Eric Wyatt's discussion Horizontal solid yellow & solid light magenta stripes
"The screen covering the nozzles should be flat. However you do get some creases from brushing media or clamps. They will deflect the nozzles if it goes far enough up and those are not recoverable. You have something going on further back that I…"
Nov 30, 2018
Eric Wyatt replied to Eric Wyatt's discussion Horizontal solid yellow & solid light magenta stripes
"So I think I found the problem according to the attached photo of the Print Head. Shouldn't the Print Head be flat? Notice the "dimples"? What are your thoughts?"
Nov 30, 2018
irving donaldson replied to Eric Wyatt's discussion Horizontal solid yellow & solid light magenta stripes
"OK great we are talking the same, just needed to make sure.  Cleanings are not helping. You replaced the parts that would affect it. If you are sure the lines from the waste bottle to the cap, to include the connectors are clear, then I am…"
Nov 30, 2018
Eric Wyatt replied to Eric Wyatt's discussion Horizontal solid yellow & solid light magenta stripes
"The encoder strip I clean is located directly in front of the carriage belt.Attached is the most current results of a test pattern. As always any suggestions you have is very much appreciated."
Nov 30, 2018
irving donaldson replied to Eric Wyatt's discussion Horizontal solid yellow & solid light magenta stripes
"The encoder strip you cleaned is located where? The fill pattern will not clear up until you clear up the nozzle test so not happy with the test checking to see what else, but you did the normal culprits."
Nov 28, 2018
Eric Wyatt replied to Eric Wyatt's discussion Horizontal solid yellow & solid light magenta stripes
"Hi, Irving, I replaced the cap top earlier today. It was very easy. I have also preformed a number of Powerful CL. Attached are the results. A nice improvement on the Test Pattern but not so much on the Fill Print Test. Can you think of any other…"
Nov 28, 2018
irving donaldson replied to Eric Wyatt's discussion Horizontal solid yellow & solid light magenta stripes
"No worries we have to eliminate all the basics - as Todd suggested wiper, felt, and the others top, encoder and we can then go further. Always post a nozzle test for that shows a lot and health of the machine."
Nov 27, 2018
Eric Wyatt replied to Eric Wyatt's discussion Horizontal solid yellow & solid light magenta stripes
"Thank you very much for your suggestions. I have ordered a replacement Captop. It should be here tomorrow. I will keep you posted regarding the results.Thank you again. I really appreciate it."
Nov 27, 2018
irving donaldson replied to Eric Wyatt's discussion Horizontal solid yellow & solid light magenta stripes
"OK great - the light nozzle pattern is CL - that is excellent All VS captops are rated for 6 months With the 7 color set up you can get maybe a year - longer under some circumstances You have been around a good 2 years and no  telling how old…"
Nov 27, 2018
Eric Wyatt replied to Eric Wyatt's discussion Horizontal solid yellow & solid light magenta stripes
"No. My set up is CMYK LM LC LK CL.Also, I have never changed the cap."
Nov 27, 2018
irving donaldson replied to Eric Wyatt's discussion Horizontal solid yellow & solid light magenta stripes
"Your VS is set up with white? Do you have white installed, if so when was your last captop change?"
Nov 27, 2018
Eric Wyatt replied to Eric Wyatt's discussion Horizontal solid yellow & solid light magenta stripes
"Thank you for your reply and suggestion, Irving. I cleaned the encoder strip about 2 months ago. I was happy to see that it had very little ink on it.But just to be sure I cleaned it again today but with no improvement to the issue.Any other…"
Nov 27, 2018
irving donaldson replied to Eric Wyatt's discussion Horizontal solid yellow & solid light magenta stripes
"Use an alcohol pad and clean both side of your encoder strip. The pattern is coming from the traveling nozzles seen in your nozzle test. "
Nov 27, 2018
Eric Wyatt replied to Eric Wyatt's discussion Horizontal solid yellow & solid light magenta stripes
"Thank you for your reply and suggestions, Todd. I replaced both wipers this past September."
Nov 27, 2018

Profile Information

Hometown: Please include City & State
Fort Myers
Core Business
Other
Your Position
Vice President
Website:
http://www.Wrapster.biz
Type of Printer/Cutter if owned:
VersaCamm VS-640i

Eric Wyatt's Photos

  • Add Photos
  • View All

Eric Wyatt's Videos

  • Add Videos
  • View All

Comment Wall

You need to be a member of MyVersacamm.com to add comments!

Join MyVersacamm.com

  • No comments yet!
 
 
 

© 2019   Created by Steven Jackson - Admin.   Powered by

Badges  |  Report an Issue  |  Terms of Service