Donovan
  • Male
  • United States
Share on Facebook
Share
  • Blog Posts
  • Discussions (24)
  • Events
  • Photos
  • Photo Albums
  • Videos

Donovan's Discussions

Wrong colors and black drag marks Express Print

Started this discussion. Last reply by chris wool Aug 26. 6 Replies

Using stahls express print many times it prints perfectly but seem anthing with black in it it starts out as correct colors then shifts colors after the first couple passes. To get around this I…Continue

Right profile bad print express print

Started this discussion. Last reply by irving donaldson Aug 1. 4 Replies

I bought my printer to mainly print on heat transfer vinyl. I have stahls…Continue

Wipers installed wrong? Sp 300i

Started this discussion. Last reply by irving donaldson Aug 1. 1 Reply

I bought a sp300i a couple weeks ago replaced the captops a few days ago and replaced wipers today. When I took the wipers out the felt was facing the front of machine. My owners manual says rubber…Continue

Test prints and calibration help

Started this discussion. Last reply by irving donaldson Aug 25. 30 Replies

I have a Sp 300i I bought used a couple weeks ago. It has been printing great with slight banding on some black colors.  From the reading the forum I’ve learned some banding can come from feed…Continue

Gifts Received

Gift

Donovan has not received any gifts yet

Give a Gift

 

Donovan's Page

Latest Activity

chris wool replied to Donovan's discussion Wrong colors and black drag marks Express Print
"don't think that half of the black cyn head will recover and certainly will not help banding in its present state. idea to check the damper flow is to print at a lot slower speed and put a delay in between passes if available. the streaking i…"
Aug 26
irving donaldson replied to Donovan's discussion Test prints and calibration help
"What does the nozzle test looks like now. The only other issue would be damper, captop, clogged lines not keeping up.  If you are printing with cleaning cartridge, and it runs clear then back to black. That means something is wrong with the…"
Aug 25
irving donaldson replied to Donovan's discussion Wrong colors and black drag marks Express Print
"The correct look is - columns are equally spaced - overlap or space in the middle means it is off. With your nozzles and that pattern - you cannot get a proper reading."
Aug 25
Donovan replied to Donovan's discussion Test prints and calibration help
"Sorry for not replying sooner. I’m on the verge of replacing the black head (sp300i) but trying to clarify my issues before doing so.  I continued running cleaning solution until it was clear solution coming from the head. My test…"
Aug 23
Donovan replied to Donovan's discussion Wrong colors and black drag marks Express Print
Aug 22
irving donaldson replied to Donovan's discussion Wrong colors and black drag marks Express Print
"Color profiles dictates to the machine how the ink is distributed and at what levels Some profiles call for different ink levels - if the one you are using is calling for ink that is not there due to nozzle drops or not capable of keeping up with…"
Aug 22
Donovan replied to Donovan's discussion Wrong colors and black drag marks Express Print
"Sp 300i Replaced captop three weeks ago Ink is Roland ecosol max"
Aug 22
irving donaldson replied to Donovan's discussion Wrong colors and black drag marks Express Print
"Need the following: - how old the captop - the ink configuration - the machine - Nozzle test"
Aug 20
Donovan posted a discussion

Wrong colors and black drag marks Express Print

Using stahls express print many times it prints perfectly but seem anthing with black in it it starts out as correct colors then shifts colors after the first couple passes. To get around this I switch to the TTRH profile and it prints the correct colors but leave black streaks all over the print.  I’ve cleaned the print heads and carrier no fuzz etc. this has been happening for a couple weeks. Picture below shows example of what I’m getting. Blacks turn to blue using express print profile.…See More
Aug 19
irving donaldson replied to Donovan's discussion Test prints and calibration help
"Still having issues following most of  your postings Seems as if you are still printing while trying to clear the first problem. So since colors still need black to make other colors, then you are putting back in the black. Thus it does take a…"
Aug 8
Donovan replied to Donovan's discussion Test prints and calibration help
"Ran lots of cleaner but still pretty much have the same nozzle test prints with the black head. I think a new head will be needed to fix the banding issue. I have another problem now though my prints have started get light black drag marks across…"
Aug 8
irving donaldson replied to Donovan's discussion Test prints and calibration help
"Also remember the lines holds lots of ink, so if you kept the cartridge out and still getting black ink - there is something you are leaving out telling us"
Aug 7
irving donaldson replied to Donovan's discussion Test prints and calibration help
"Did you check convert spot colors Did you check preserve primary colors in color management properties Are you using BK21A Not really surprized if you are loosening and not getting the ink that was dried - what I see is not solid but I do not know…"
Aug 7
Donovan replied to Donovan's discussion Test prints and calibration help
"This is what it went back to printing. "
Aug 3
Donovan replied to Donovan's discussion Test prints and calibration help
"Also when I started printed cleaning fluid tonight it started out with banding black color then went to a gray mist but after about 25 -30 minutes or printing these black square and starting over printing them again with the same gray must color I…"
Aug 3
Donovan replied to Donovan's discussion Test prints and calibration help
"One more question. When I trying to print 100% black with cleaning cartridge should I check convert spot color box in Versaworks. Seems if I don’t it mixes the other colors I think "
Aug 3

Profile Information

Hometown: Please include City & State
Lexington, Kentucky
Core Business
T-shirt Shop
Your Position
Owner
Type of Printer/Cutter if owned:
Roland Versacamm SP 300i

Comment Wall

You need to be a member of MyVersacamm.com to add comments!

Join MyVersacamm.com

  • No comments yet!
 
 
 

© 2019   Created by Steven Jackson - Admin.   Powered by

Badges  |  Report an Issue  |  Terms of Service