David R. Cunningham
  • Male
  • Kissimmee, FL
  • United States
Share on Facebook
Share

David R. Cunningham's Friends

  • dan tanner

David R. Cunningham's Discussions

VP540i Print Issue

Started this discussion. Last reply by irving donaldson May 10. 3 Replies

Well, I've solved the issue of the scan motor the rail guides and everything else. The issue that I'm having now is when I did a test print my yellow continues to print without stopping. I've tried…Continue

VP540i Scan Motor Errors

Started this discussion. Last reply by irving donaldson Apr 30. 9 Replies

Ok folks... I have an issue. I own a VP540i and I am constantly getting multiple Scan Motor Errors. (0040, 0080 & 0090). However, this is the issue... It appears as the motor is good, but the…Continue

Gifts Received

Gift

David R. Cunningham has not received any gifts yet

Give a Gift

 

David R. Cunningham's Page

Latest Activity

irving donaldson replied to David R. Cunningham's discussion VP540i Print Issue
"Nope, do not agree. What you have is called blocked printing. I spoke to it before. When you replaced the cables you did not align them correctly. Something as simple as not having the two cables aligned with one another and then parrelell to the…"
May 10
David R. Cunningham replied to David R. Cunningham's discussion VP540i Print Issue
"Come to find out, there are allen screws on both ends of the guide.  The replacement guides are SSR15XW1UU. What the screws are attached to are "Grit Scrapers"  Each rail on a printer is different and the guides that come with…"
May 10
irving donaldson replied to David R. Cunningham's discussion VP540i Print Issue
"How did you solve the rail issue?"
May 9
David R. Cunningham posted a discussion

VP540i Print Issue

Well, I've solved the issue of the scan motor the rail guides and everything else. The issue that I'm having now is when I did a test print my yellow continues to print without stopping. I've tried multiple cleanings and now this is the issue that I'm having. I'm slowly breaking this printer back down, I'm bringing it back to life. It doesn't matter if I do a test print or anything that I print I get the yellow to continuously fire. I have enclosed an image to show what I am seeing. Any ideas?
May 9
David R. Cunningham replied to Jim Cain's discussion l bearing sp300v
"https://lavaink.com/Inks-Parts/ This is who I used.  Good price and BOY I have learned a lot with this printer and I can help if you have any issues..."
May 9
David R. Cunningham posted a status
"What is the screw installation pattern for a VP540i?"
May 2
David R. Cunningham posted a photo
May 2
irving donaldson replied to David R. Cunningham's discussion VP540i Scan Motor Errors
"All measurements are in the manual.  Manually move the cutter with machine off and see if the belt is binding on the pulley"
Apr 30
David R. Cunningham replied to David R. Cunningham's discussion VP540i Scan Motor Errors
"I have tried to run the aging, however, the Scan Motor error comes up prior to cycling.  I have cleared ALL ERRORS in memory. I even tried setting Base Point towards the far left of material and running a test print. Got the Motor Error again,…"
Apr 30
irving donaldson replied to David R. Cunningham's discussion VP540i Scan Motor Errors
"The error and effects seems to be a Deviation Error whereas the order from the CPU does not match the feedback being reported by the Scan Motor.  (could be a servo board error) but before that: - grease lubrication the motor gear, then  -…"
Apr 28
irving donaldson replied to David R. Cunningham's discussion VP540i Scan Motor Errors
"Checking - do not answer chats"
Apr 28
David R. Cunningham replied to David R. Cunningham's discussion VP540i Scan Motor Errors
"Ok... About to loose my mind.... I have replaced a Scan Motor and all 3 of the Linear Motor Guides. I am still getting a Scan Motor Error 0090 0080. The error does not come up until you put the head in motion from an actual print job. It will print…"
Apr 28
David R. Cunningham replied to David R. Cunningham's discussion VP540i Scan Motor Errors
"Well....  I got the motor and it's not the motor.  I went further into diagnosis mode and found the problem(hopefully).  As the cutter carriage slides, it appears that the Linear Motion Guides are bad.  That is…"
Apr 21
irving donaldson left a comment for David R. Cunningham
"If the motor is bad, you would expect an error on boot up. Once the machine cycles through a normal clean, it will attempt to do a media measurement. You will likely throw an error since it is attempting to move left and it is not moving at the…"
Apr 19
irving donaldson replied to David R. Cunningham's discussion VP540i Scan Motor Errors
"Scan - is the left to right or your X axis. Just stating so we are talking the same apples. The errors you are getting are Left to Right errors. So I would ask unless you some how bent the rail it rides on, or elevated the planten, what is causing…"
Apr 19
irving donaldson replied to David R. Cunningham's discussion VP540i Scan Motor Errors
"What makes you think the motor is good. Those are basically the same errors. You get the 10, or the 80 and the 90 is both. The motor is jamming and causing an overcurrent error.""
Apr 19

Profile Information

Hometown: Please include City & State
Jeffersonville, Indiana
Core Business
Embroidery, Screen Printing, T-shirt Shop, Graphic Designer, Promotional Company
Your Position
Owner
Website:
http://CustomThreadsandInk.com
Type of Printer/Cutter if owned:
Roland VP540i, Multiple Epilog Lasers
Type of Heat Press if owned:
Stahls Fusion and Hotronix

David R. Cunningham's Photos

Loading…
  • Add Photos
  • View All

Comment Wall (2 comments)

You need to be a member of MyVersacamm.com to add comments!

Join MyVersacamm.com

At 3:26pm on April 19, 2017, irving donaldson said…

If the motor is bad, you would expect an error on boot up. Once the machine cycles through a normal clean, it will attempt to do a media measurement. You will likely throw an error since it is attempting to move left and it is not moving at the correct speed - over temp reading. The cutting assembly is pulled by the motor attached to the belt. The drag comes from the printer assembly which is attached by a magnet.

At 12:24pm on April 19, 2017, irving donaldson said…

What makes you think the motor is good. Those are basically the same errors. You get the 10, or the 80 and the 90 is both. The motor is jamming and causing an overcurrent error.

 
 
 

© 2017   Created by Steven Jackson - Admin.   Powered by

Badges  |  Report an Issue  |  Terms of Service